Model #GW395LEGQ5 WHIRLPOOL Slide-In Range, Gas

  • Cooktop/literature
    3 Results
  • Control Panel
    3 Results
  • Cooktop Burner
    3 Results
  • Broiler And Oven Burner
    3 Results
  • Door And Drawer
    3 Results
  • Oven Chassis
    3 Results
  • Rear Chassis
    3 Results
Find part by diagram >

Question and Answers

Q:

Help! on my gw395legq5 door trim GW395legq5

A:

I can understand how important it is to have the right information for your range. On this model, from what I could see the trim is around the outside of the door, and it is screwed into place.  Just remove and replace the screws.   I hope this helps. Please feel free to let me know if you need further assistance. We are always here to help. Thank you for using Manage My Life.com.

Read More
AnneJ -
Sears Technician
September 23, 2013
Q:

do you have instructions on how to install a glass part on my range - model # GW395LEGq5

A:

I can appreciate your need for proper instruction regarding this glass top replacement.  I've research and I've noted that this might be a gas stove.  So I'm not sure if it's the glass top that you cook on that you want to replace because being gas there is no glass top.  If we are not talking about a glass top, would you please let me know what glass part we are talking about?  If I'm mistaken and it is a glass top that you cook on that you want to replace, I did find some good instructions for a Kenmore.  Click here to view the link.  Though this link discusses a different model number and manufacturer,
the mechanics are likely going to be very similar. Keep in mind that an expert will be
responding within the next two business days if not sooner and will likely offer you more information and
instruction. I hope this information will be helpful and have a nice day.

Read More
Henry -
July 11, 2013
A:

Thank you for your question and I understand your concern.

I added an image below with the procedure. It may not be exactly the same as your model but it was the closest instructions I could locate.

NOTE: Disconnect the power cord from the power source before servicing. 

I hope this is helpful. If I may be of further assistance as more details become available, please reply to this post. 

Read More
Joey S -
Sears Technician
July 12, 2013
A:

Joey, thanks for your response. The glass I'm needing to replace is on the door of the range. It's the inside glass. not on the oven top. My range is equiped to use gas and I have gas burners.. So, if you open the range door, it's the top glass on the door. I don't see any screws on top of the door, therefore, I don't see how to remove the door to get to the broken glass. Also, I don't see how to remove the hinges to get the door away from the range in order for me to access the broken glass. Again, that's model number GW395LEGQ5. If you look on a 'schmetic diagram' of the model, it's item # 15 on the diagram. (Rosalyn)

Read More
rosalyn -
July 12, 2013
A:

Rosalyn; I added two images below showing how to remove the door and how to take the door apart. The top left image in the first image I provided should be specific to your model for removing the door. Once the door has been taken off, the two screws securing the handle must be taken off and all the screws along the bottom of the door. The door can now be separated to access the inner door glass. Note, pay close attention to how the parts are assembled before removing. Take pictures if needed.

Read More
Joey S -
Sears Technician
July 12, 2013
See more answers
Q:

oven burner

A:

I'm sorry that you are having some difficulties with your Whirlpool Gas Range. I did some research for you at Managemylife.com and found an expert answer to a similar question that may help you until your expert can respond to your specific question. The link is attached below. Please remember that the expert is able to walk you through a repair like this and even help you order any required parts. If you do decide to schedule service and have a qualified technician help you, I have also attached a link to Searshomeservices.com.

Read More
James -
July 19, 2011
A:

Thank you for your question and I understand your concern.

Based on your symptom the Bake ignitor is right on the edge of being too weak to open the gas valve. If the ignitor does not pull enough current/amperage the gas valve will open. I must assume you know how to access the bake burner and ignitor by removing the floor of the oven and flame spreader.

Replace the Bake ignitor and your oven will ignite and operate normally again. The Bake ignitor is part #9782065 which can be ordered from Sears PartsDirect . NOTE: Disconnect the power cord before accessing and replacing the ignitor.

Read More
Joey S -
Sears Technician
July 20, 2011
See more answers