Model #GU2400XTPT6 WHIRLPOOL Dishwasher

  • Door And Panel Parts
    3 Results
  • Control Panel Parts
    3 Results
  • Door And Latch Parts
    3 Results
  • Lower Washarm Parts
    3 Results
  • Heater Parts
    3 Results
  • Fill And Overfill Parts
    3 Results
  • Tub And Frame Parts
    3 Results
  • Pump And Motor Parts
    3 Results
  • Upper Rack And Track Parts
    3 Results
  • Upper Wash And Rinse Parts
    3 Results
  • Lower Rack Parts, Optional Parts (not Included)
    3 Results
Find part by diagram >

Troubleshooting

Error Codes

Error Code:

Condition:

Check/Repair:

Question and Answers

Q:

GU2400XTPT6 Dishwasher doesn't rinse after wash cycle.

A:

I'm sorry about the difficulties you're having with your dishwasher.  While you are waiting for an expert to respond, I have added a helpful link (click here) that may provide information to assist you with your question.

Read More
Yadira B -
July 30, 2013
A:

Thank you for your question and I understand your concern.

Based on your symptom and details, I must assume the drain pump is jammed or faulty. You will need to remove the front lower access panels and check to see if the drain pump is jammed. If the drain pump hums instead of running and pumping water out; it's likely getting the proper voltage supply (120). The drain pump can be easily remove and check for any blockages.

NOTE: Disconnect the dishwasher from the power supply before removing the lower access panels.

I added an image below with the procedure of removing the drain pump.

I hope this is helpful. If I may be of further assistance as more details become available, please reply to this post. 

Read More
Joey S -
Sears Technician
July 31, 2013
A:

Thanks for the tip, Joey, however, it drains just fine. Any other suggestions?

Read More
Geoffrey -
August 01, 2013
A:

Geoffrey: So you say it will fill and wash and then hums? After the washer cycle is completed, the next step is to drain the water out. If it drains water and washes then I guess I do not fully understand what is going on. You say it will drain, but how to get it to drain if it just hums after the wash cycle is completed? If will not drain in the cycles but will if you press Cancel/Drain, then I would have to suspect a control board issue. If you would add additional details I may have better understanding of the problem. When it hums, let it hum a minute or and then open the door and see if drained.

Read More
Joey S -
Sears Technician
August 02, 2013
A:

Yes, if I open the door after the wash cycle, it has drained, but if I check during the rinse cycle, there is no new water inside. It just seems like things are heating up.

Read More
Geoffrey -
August 02, 2013
A:

Geoffrey; Okay now I understand; it's not always filling with water. Check the float dome in the front corner of the tub. If for some reason the float is rising and sticking in the up position, the float switch will open and break the electrical circuit to the water inlet valve. Slowly raise and let the float lower and make sure it comes all the way down and trip the micro switch up under the tub. You may need to leave the water inlet valve connected and place the voltage meter leads across the two wires terminals connected to the water inlet valve and sit there and monitor the voltage to the water inlet valve. It should always refill with water after a few seconds after it competes the drain cycles. Note: I do not recommend monitoring the voltage to the water inlet valve unless you have experience and feel safe and confident in doing so; otherwise I recommend calling a service technician to diagnose and repair your dishwasher.

Read More
Joey S -
Sears Technician
August 05, 2013
A:

Sorry for the long delay. So to try and be more specific, here's my attempt: The machine fills and runs the wash cycle, then drains just fine. Once that happens, it does not refill for the rinse cycle. I've checked the float, and it does not seem to stick, nor does the filter seem clogged because it drains just fine. Someone suggested that it might be the circuit board. I'm assuming that's part #8564547? Someone else suggested the door latch, but I couldn't figure out that part number. Why would the latch stop it from rinsing, but allow it to wash?

Read More
Geoffrey -
August 29, 2013
A:

Geoffrey: The door latch and door switch would not relate to the dishwasher not re-filling after the first wash and drain cycle has completed. It's beginning to sound like a control board issue if the control is not supplying the 120 volts to the water inlet valve assembly after the initial fill and wash cycle. I would have to assume a component on the control could be failing after the component gets hot. I added an image below showing how to run a diagnostic test to see if fills during the test. Again, it sounds like it will need a new control board if the control is not providing voltage to the water inlet valve when it should be filling. The part number of the control is 8564547.

Read More
Joey S -
Sears Technician
August 29, 2013
A:

Thanks, Joey. I just got a call from a dishwasher repair guy I had come look at it. He thinks it's the water valve. I'm assuming this is the "inlet valve, #8531670." Since I'm not home, I don't know if he tested the control board.

Read More
Geoffrey -
August 29, 2013
A:

Geoffrey: It's odd that it will fill the first time and not the second time? I hope the technician can properly diagnose and repair the issue for you.

Read More
Joey S -
Sears Technician
August 29, 2013
See more answers
Q:

Why Does My Undercounter Dishwasher Leave Suds At The Bottom Of THe Drain Holes

A:

Residual suds left on the bottom of the tub after a completed wash cycle could be caused by:

  • Using too much detergent for the type of water conditions (if you have a water softener use less detergent)
  • Wrong kind of detergent (I recommend Cascade powder)
  • Rinse agent leaking into the wash/rinse water (look for a trail of rinse agent under the dispenser assembly)
  • Rinse agent set to dispense too much rinse agent
  • Value branded detergent (buy name brands)
  • Dishwasher not filling with enough water
  • Pre-rinsing dishes
  • Using one of those rinse aide baskets hung from the rack.
  • Soft water

Read More
Joey S -
Sears Technician
April 29, 2010

Top Parts