Model #GU1500XTKQ0 WHIRLPOOL Dishwasher

  • Door And Panel Parts
    3 Results
  • Control Panel Parts
    3 Results
  • Door And Latch Parts
    3 Results
  • Lower Washarm Parts
    3 Results
  • Heater Parts
    3 Results
  • Fill And Overfill Parts
    3 Results
  • Tub And Frame Parts
    3 Results
  • Pump And Motor Parts
    3 Results
  • Upper Rack And Track Parts
    3 Results
  • Upper Wash And Rinse Parts
    3 Results
  • Lower Rack Parts
    3 Results
  • Miscellaneous Parts Optional Parts (not Included)
    3 Results
Find part by diagram >

Troubleshooting

Error Codes

Error Code:

Condition:

Check/Repair:

Question and Answers

Q:

My whirlpool Gold dishwasher is no longer washing...

A:

Good morning J.... I think I'd rather have the noise then the dirty dishes. Do you think that hard water has plugged the arms that spray in any way do you? Are the arms rotating? I did locate a link that will discuss your situation in greater detail. Though this link discusses a different model number, the mechanics are likely going to be very similar. Keep in mind that an expert will be responding within the next two business days if not sooner and will likely offer you more information and instruction. I hope this link will help guide you as to what might be wrong with your dishwasher and have a nice day.

Read More
Henry -
April 29, 2013
A:

I know that it can be very frustrating to have issues with your dishwasher.  There are several components that can make a strange noise, then stop working. These include the inlet valve, the pump, or the motor.  Since you do not mention if the unit is filling with water, I am assuming that it is.  If this is the case, then you are looking at either the pump or the motor being the issue.  Normally I would suggest running a diagnostics cycle, but since the timer is counting down, it won't work.  The parts will need to be tested with an ohm meter to find the defective one.  This testing can be very complicated, so I would suggest that you have a technician do this for you. If you would like to schedule just click on this link: Sears Home Services.  If you need further assistance, please reply to this thread. Thank you for using Manage My Life.

Read More
AnneJ -
Sears Technician
April 30, 2013
See more answers
Q:

How do I remove the inlet protector from my Whirlpool dishwasher model GU1500XTKQ0?

A:

Once you remove the screw from the inlet protector, it should lift straight up and out of the sump. The image below shows the basic procedure for accessing the chopper blade area under the inlet protector. Since you have already removed the screw that secures the inlet protector, I recommend that you try to use a flat tip screwdriver to carefully pry the inlet protector up and out of the sump or use a pair of pliers to lift it out. If you are not able to remove it, I recommend that you call a service technician to repair the dishwasher.

Read More
Lyle W -
Sears Technician
December 07, 2009
A:

There is a little clip hidden on the righthand side (opposite to the screw). You need to pop a thin screwdriver in between the cover and base push it toward the chopper. Note that the cover extends just a bit past the place for the clip.

Read More
Matthew -
November 24, 2012
A:

Note - I just did this 10 minutes ago....

Read More
Matthew -
November 24, 2012
A:

If you look at page 9 of this: https://www.whirlpool.com/digitalassets/MLPDF/Repair%20Part%20List%20-%208193807.pdf Part 8 on that page is the cover. You can just make out the clip on that figure.

Read More
Matthew -
November 24, 2012
See more answers

Top Parts