Model #GSS22JETECC GE Side-by-Side Refrigerator

  • Freezer Door
    3 Results
  • Fresh Food Door
    3 Results
  • Freezer Section
    3 Results
  • Freezer Shelves
    3 Results
  • Ice Maker & Dispenser
    3 Results
  • Fresh Food Section
    3 Results
  • Fresh Food Shelves
    3 Results
  • Sealed System & Mother Board
    3 Results
Find part by diagram >

Error Codes

Error Code:

Condition:

Check/Repair:

Question and Answers

Q:

NO water from dispenser still makes ice GSS22JETECC Ge Refrigerator t series

A:

Hello glad to help.  Thank You for choosing Sears PartsDirect.com
 
I am sorry and do understand your frustration when there is problems with the refrigerator.
 
Glad to help out.   Im  looking at your GE Refrigerator model number  GSS22JETECC.

HOW TO VERIFY WATER VALVE FOR THE GE REFRIGERATOR:

1.  Pour around a 1/2 cup water into the ice maker mold if your ice maker is either not producing ice or is producing less ice or smaller cubes. If the ice maker produces ice properly within about two hours, it is functioning properly and the problem is probably in the water valve. If it doesn't produce ice, the ice maker might malfunctioning.

2.  Pull the refrigerator out from the wall to access the water valve. Close the water valve and then open it again.  Might be a restriction at the valve such as ice or scale can reduce the water supply, which may result in smaller cubes. This opening and closing causes the valve to pierce the opening in the water line and may remove the blockage.

3.  Remove the water filter and then replace it with a new one. Clogged water filters can also cause decreased ice cubes or water.

4.  Test the water valve to determine whether it is working properly by disconnecting the power supply to your refrigerator first.

5.  Close off the main water supply shut-off valve located on the water line that feeds your water inlet valve.

6.  Take off the access panel on the back of your refrigerator using the screwdriver. Disconnect the fill tube that is connected to the valve.

7.  Loos the nut on the brass fitting located on the inlet side of your valve. Use an adjustable wrench and then remove the screws in the metal bracket that holds the water valve in place to pull the valve out of the refrigerator.

8.  Remove the filler tube from the water valve port. Disconnect the wires connecting the water valve to the refrigerator. Label each wire so you disconnect it to remember where it will go later.

9.  You can test the valve’s terminal using a multimeter. If it reads around 200 to 500 ohms, or the reading indicated on the valve itself, the terminal is functioning fine. If it does not read in this range, then replace the valve.

10.  Take out the ice maker from the refrigerator and inspect the fill tube, which is the plastic tube above your icemaker. If the tube is frozen, it may cause the icemaker to leak water inside the ice bucket or onto the floor.

11.  Warm the fill tube using a hair dryer but set on its lowest setting or wrap the tube in  a warm cloth to thaw the ice. If the tube is frozen solid, you may have to replace the water inlet valve and tubing.

12.  Then make sure that all connections to the water valve and the ice maker are secure and are not leaking water.

13.  Pull the refrigerator out from the wall and disconnect the power supply. Remove the access panel at the back of your refrigerator using a screwdriver. Inspect the water fill valve for any moisture or cracks.

14.  Try to close off the valve manually. If it is stuck open, the valve is malfunctioning or blocked and should be replaced by a qualified technician.

Please "RESUBMIT YOUR QUESTIONS IF THERE IS ANY OTHER PROBLEMS".
 
Thank you for your understanding in this matter and I hope we can help you with your future questions and repairs.  Thank you for choosing Sears and using our SearsPartsDirect.com.

Read More
Larry L -
Sears Technician
April 18, 2014
Q:

Refrigerator makes ice stopped dispensing water filter is good GSS22JETECC Ge Refrigerator t series

A:

The information you have received is good. Press the lever in slowly and listen for a clicking sound. If you do not hear this sound, it will indicate that either the switch has failed or the actuator is not making contact with the switch. Remove the front cover and you will be able to see the switch and what is happening. I’m attaching a picture of how to remove the front cover. Be sure to disconnect the power first.

If you do hear the clicking sound, the problem could be with the motor or a wiring problem. With the power disconnected, remove the top door hinge and you will see a harness connection. First, make sure the connection is tight and there are no loose wires. If the connection appears ok, a voltage check will need to be made between the blue and white wires. Reconnect the power and press the door switch in and activate the lever. If there is 120 volts between these wires, it will indicate the motor # WR60X10230 has probably failed and will need to be replaced. It could be a loose wire connection between the hinge and motor but it would be very unlikely. I hope this will help you. I have included a link to our PartsDirect page where you can purchase the part you need to complete your repair. Just click the blue link above to be taken to the page. If you have further questions please resubmit your question for further information.

 
Thank you for choosing Sears PartsDirect.com.
 
SAFETY NOTICE: Be sure to disconnect power to the appliance before performing any repairs. If you are not comfortable with doing any voltage checks that might be recommended, please contact Sears for repairs. Be aware that there could be sharp edges inside the appliance that could cause cuts or other injuries to yourself or others.

Read More
Sherman_G_Wallace -
Sears Technician
April 09, 2014
A:

Thank you for the quick reply there was no photo attached showing how to remove front cover #1 My problem is no water dispensing. water switch does make a clicking noise and i hear a wineing noise when depressed all the way attached air and vacum so it can not be a air bubble i think it could be a water pump the motor # wr60x1023 you mentioned is a ice crusher motor thanks please advise Frank

Read More
Frank -
April 16, 2014
See more answers
Q:

GE model gss22jetecc Refrige side no cooling

A:

I know how disappointing it is when your refrigerator will not cool. I was able to find a link for a GE refrigerator that won't cool. I attached the link below. An expert will respond shortly. I hope all goes well.

Read More
Jackie S -
August 16, 2012
A:

Thank you for your question. I'm sorry you are having this problem with your fridge. This type of problem is normally caused by poor air flow. Check to see if there is a thick frost accumulation on the back wall in the freezer. As the frost builds, the air flow will be reduced. If there is a thick frost, it will indicate a problem with the defrost system. In this case, move the food out of the freezer, leave the door open and turn the unit off for 24 hours. This will allow time for it to defrost. When it's completely defrosted, it will cool properly again for a few days until the frost builds back up again. This will give you a chance to have it checked.

If there is no frost accumulation, the problem could be with the sensor, the control board or the air diffuser. These are checks a technician will need to make. I'm listing a site you can access, to have a tech come out. Here is a link for the website: Sears Home Services . I hope this will help you.

Read More
Scott D -
Sears Technician
August 18, 2012
See more answers

Top Parts