Model #GSD900G-01 GE Dishwasher

  • Tub And Door Assembly
    3 Results
  • Control Panel And Motor-pump Assembly
    3 Results
Find part by diagram >

Troubleshooting

Error Codes

Error Code:

Condition:

Check/Repair:

Question and Answers

Q:

Detergent lid will not stay closed. GSD900G-01 Ge Dishwasher

A:

Thank You for choosing Sears PartsDirect.com. I regret to hear that you are having issues with your dishwasher 
and do understand your frustration. Glad to help out. Im looking at your model number GSD900G-01 and it possible that the latch is damaged or needs adjustment. I have included a video that will help with this problem. These are the parts that I recommend checking, trip spring, and detergent cup latch
 
I have included a link to our PartsDirect page where you can purchase the part you need to complete your repair. Just click the blue link above to be taken to the page.
 
If you have further questions please resubmit your question with a additional details. Thanks for choosing Sears PartsDirect.com
 
 
 
.
 

Read More
Sherman_G_Wallace -
Sears Technician
February 27, 2014
Q:

GE Dishwasher GSD900G-01 Why doesn't the water pump out anymore?

A:

The dishwasher is a very important appliance since it keeps the dishes nice and clean. I am adding a link below to help you with your question while you wait for your expert response.

Read More
Joseph P. -
January 25, 2012
A:

Thank you for your question and I understand your concern.

In order for your model to drain water the drain solenoid must energize and pull down the linkage connected to the drain flapper valve. You will need to remove the toe plate and access panel and watch the drain solenoid operation when you advance the timer to a drain cycle. The solenoid must pull down the metal plunger located in the center of the solenoid. The plunger connects to some linkage which connects to a flapper valve located inside the drain fitting that the drain hose is connected to. I added an image below of the drain solenoid. You should also be able to manually push the plunger down if the coil has not overheated and warped. Do not touch the any wires or terminals while the dishwasher is connected to power. If the drain solenoid is energizing and pulling the plunger down and it does not drain then I would suspect a blockage in the drain hose or where it connects under the sink.

I hope this is helpful. If I may be of further assistance as more details become available, please reply to this post.

Read More
Joey S -
Sears Technician
January 27, 2012
See more answers
Q:

i have a ge dishswasher model gsd900g-01wa. i need to replace the detergent trip spring. is there a diagram online so i can see how it should be installed?

A:

I'm sorry to hear that you are having some difficulties with your GE Dishwasher. I did some research for you at Managemylife.com and found an expert answer to a similar question that may help until your expert can respond to your specific question. The link is attached below. The expert who will assist you, can walk you through a repair like this or let you know if this may be something a technician should perform. He can also verify parts that may be required for you to order. If you do decide to schedule service and have a qualified technician help you, I have also attached a link to Searshomeservices.com. I hope these links provided will assist you.

Read More
James -
September 21, 2011
A:

Thank you for your question and I understand your concern.

There are no good diagrams illustrating were the spring attaches. The link James R. added in the first response shows an image that may help. I also added an image below and in which I drew a red arrow showing where the spring attaches on the dispenser cup arm. The other end of the spring will connect to a short plastic post molded in the plastic console. If the post is broken you can heat up a paper clip and melt a small hole though the plastic edge next to the broken post to connect the spring to.

I hope this is helpful. If I may be of further assistance as more details become available, please reply to this post.

Read More
Joey S -
Sears Technician
September 23, 2011
See more answers