Model #GSD580P-35BA GE Dishwasher

  • Control Panel And Door
    3 Results
  • Tub Assembly
    3 Results
  • Motor-pump Assembly
    3 Results
Find part by diagram >

Troubleshooting

Error Codes

Error Code:

Condition:

Check/Repair:

Question and Answers

Q:

dishwasher leaking

A:

A dishwasher can save time and energy or it can ruin our day when it is leaking. A suggestion I have to help the expert provide a better answer is to add the model number to this thread. That way the answer will be specific to your dishwasher. While you wait for the expert, I did find two pretty good sites with helpful general checks you can make if you like. I attached the links below. Hope this helps!

Read More
Barbara H. -
September 03, 2010
A:

there is a value under the dishwasher that leads from it to ur sink. make sure it is tight. email me an i will walk u thru it. ftb41042@yahoo.com

Read More
Judy -
September 03, 2010
A:

A complete model number would help me give you a more specific answer but there are some things to consider.

Some things to check for are an incomplete drain which will allow the dishwasher to overfill the next fill cycle and possibly leak.

Excessive suds in the water might cause a leak. To much soap and not enough dirt might cause this one cycle but not the next.

A door gasket problem might cause a leak.

There is usually a lower access panel that can be removed to get a better look at the source of the leak. See the image below for what one might look like.

You can use the reply button to submit any additional details for further assistance.

Read More
Fred M -
Sears Technician
September 04, 2010
A:

Thanks Fred M After removing the acess panel I discovered the leak is underneath apparently from the gasket or asembly holding the spray arm Model # 363.14382000, purchased Sept 2000, service call $130 Should I repair or buy? No leaks from doot gasket, no excessive suds

Read More
EN -
September 04, 2010
A:

The image below shows a parts breakdown of the dishwasher which may be helpful to you. Part key 455 is the connector and it may be the source of the leak. There is a hose clamp, part key 457, that may just be loose. The connector is only about $10 dollars so it may be worth a look to see if this is a good do-it-yourself project. Most new dishwashers will start at around $229 dollars. I hope this information has been helpful to you.

Read More
Fred M -
Sears Technician
September 04, 2010
A:

ge model # gsd580 p35ba I replaced the door gasket to stop a leak but did not install from the top down but from the bottom up. And, I did not soak it in hot water before installing gasket...nor did I allow it to seat overnight with the door closed. Could that be the reason the door is still leaking?

Read More
ray -
June 07, 2012
A:

Most likely the seal is the source of the leak. A hot water soak helps the gasket mold itself to the door for the best seal.

Read More
Fred M -
Sears Technician
June 09, 2012
See more answers
Q:

Why is my washer still leaking?

A:

I understand that your refrigerator door is leaking. While you are waiting for an expert to respond, I have attached a helpful link below that may provide information to assist you with your question. Have a great day!

Read More
Alina F. -
June 07, 2012
A:

Thank you for submitting your question. I recommend installing the gasket the way that it's instructed. This could be why it's still leaking. Following the instructions allow the gasket to properly stretch and form to the dishwasher for a good seal. The way you installed it may not have given it a proper fit. I hope this helps. Please let me know if you require further assistance. Thank you for choosing Manage My Life.

Read More
Tykara -
Sears Technician
June 09, 2012
See more answers