Model #GSD4030Z07WW GE Dishwasher

  • Escutcheon & Door Assembly
    3 Results
  • Body Parts
    3 Results
  • Motor-pump Mechanism
    3 Results
Find part by diagram >

Troubleshooting

Error Codes

Error Code:

Condition:

Check/Repair:

Question and Answers

Q:

G.E Dishwasher GSD4030Z07WW not draining completely. Why?

A:

Dishwashers are a great appliance. They make life very convenient. It can be a hassle when they are not draining as they should. I did find some information for you. I am adding the links below to help you with your question while you wait for your expert response. I hope that this will help you out.

Read More
Marc H -
March 21, 2012
A:

Thank you for your question and I understand your concern.

Your dishwasher has a piston and nut assembly which can wear and prevent all the water from draining. The piston and nut assembly is located under the filter and frame assembly. (See image below.) When the rubber seal on the piston assembly becomes worn or warped, it will allow a portion of the drain water to recirculate back into the tub. You can access and remove the piston and nut assembly and inspect from inside the tub. If the rubber seal is warped or if some of it has deteriorated, replace the piston and nut assembly and your dishwasher should drain properly.

I added a couple of image below with information and instructions.

I hope this is helpful. If I may be of further assistance as more details become available, please reply to this post.

Read More
Joey S -
Sears Technician
March 22, 2012
A:

Joey - Thank you for the advise. Unfortunately the images you sent came through blank. Can you either resnd or provide link to obtain the images/instructions? Thank you Bill

Read More
Bill -
March 30, 2012
A:

Bill: I added the images again. I hope the images comes through.

Read More
Joey S -
Sears Technician
April 02, 2012
A:

Joey - Thank you, yes they came through. I will check out this part.

Read More
Bill -
April 02, 2012
See more answers
Q:

dishwasher

A:

Manage My Life is a great website to speak directly to an expert who can help you every step of the way to solving the problem you are having. An expert shall have an answer to your question within 24 to 48 hours. Have a great day.

Read More
Alina F. -
September 29, 2011
A:

Hi Denise,

Thank you for submitting a question to Manage My Life. I know how frustrating it can be when appliances do not function properly.

From your description most likely the wash pump is not working. I am including the tech sheet for this dishwasher in the images below. I recommend running the F1 test as described in the tech sheet. During step 4 of the F1 test, the wash pump should operate. If the wash motor does not run, the remaining checks will require the use of an ohm/volt meter and you will have to perform ohm checks and/or live voltage checks. If you have a meter and are confident in your ability to safely perform these checks, reply to this post and I will be happy to assist you in any way I can.

I hope this is helpful. Check the things I have covered here, and if I may be of further assistance as more details become available, please reply to this post.

If you do not feel confident repairing this problem yourself, then you can have it repaired at your home by a Sears technician. Here is a link for the website: Sears Home Services .

Here is a link that you may use to view the parts list diagram and for parts purchases; Sears Parts Direct .

Thanks again for using Manage My Life.

Landell

Read More
Landell -
Sears Technician
October 02, 2011
See more answers
Q:

What is wrong with my GE model GSD4030 built-in dishwasher when after the wash cycle and all of the water has drained out it fills up again?

A:

There are two potential causes of this problem.

The water valve is leaking water through and will need to be replaced or the drain hose has fallen and allowing water from the sink to drain into the dishwasher.

Check you drain hose for a loop above the bottom of the sink.

After a cycle and all of the water has drained out turn the water supply to the dishwasher off under the sink at the shut off spigot. If no water enters the tub by the next morning then the water valve is bad.

The part number for the water valve is WD15X93 and is available from the following link: Sears PartsDirect .

Read More
Fred M -
Sears Technician
July 25, 2009

Top Parts