Model #GSD3200G00CC GE Dishwasher

  • Escutcheon & Door Assembly
    3 Results
  • Body Parts
    3 Results
  • Motor-pump Mechanism
    3 Results
Find part by diagram >

Troubleshooting

Error Codes

Error Code:

Condition:

Check/Repair:

Question and Answers

Q:

Dishwasher stopped mid cycle GSD3200G00CC Ge Dishwasher

A:

Thank You for choosing Sears PartsDirect.com and being a valued member. It is unfortunate to hear that you are having issues with your dishwasher and I do understand your frustration. Glad to help out. I'm looking at your model number GSD3200G00CC and from your description I would suspect an issue with the door switch, item 803 or item 805. Here is a link for a video that may help with testing the switch to determine if the switch is defective. Just click the blue link above to be taken to the page. I trust this information will help you.

 

Thank you for choosing Sears PartsDirect.com.

 

SAFETY NOTICE: Be sure to disconnect power to the appliance before performing any repairs. If you are not comfortable with doing any voltage checks that might be recommended, please contact Sears for repairs. Be aware that there could be sharp edges inside the appliance that could cause cuts or other injuries to yourself or others.

Read More
Sherman_G_Wallace -
Sears Technician
January 19, 2015
A:

Sherman- Thanks for your reply. I removed the switches and tested them for continuity and I have received the exact same results for each switch. When the switch is open I received a reading of 1 on my multimeter. when I closed the circuit on the switch my reading was .4, which I assumed was a good indicator that the switch was working correctly. I'm somewhat new to using a multimeter and could be simply misunderstanding what I am seeing. Does this sound correct?

Read More
Todd -
January 19, 2015
See more answers
Q:

Dishwasher not working correctly.

A:

Dishwashers are a life saver they help with all the dishes we have. While you are waiting on an expert to answer your question, a suggestion I have is to set service with a Sears technician so you can have Dishwasher working again. Hope this helps!

Read More
Dezeray S -
September 05, 2011
A:

It doesn't help. I think you've missed the point of this forum.

Read More
Anonymous -
September 05, 2011
A:

Thank you for your question and I understand your concern.

Based on your intermittent symptoms it suggests that it may be caused by a problem with the wire harness. There was a known problem which generated a Safety Recall requiring a kit to be installed. If your dishwasher has not had the kit installed then I suggest calling GE service at 877-607-6395 and have your model number and serial number handy to see if your dishwasher is part of the Safety Recall.

If you dishwasher has had the kit installed then your symptom could be related to the installation of the kit or possibly an issue with the timer.

This may be the issue. If not, please reply and I will be glad to assist you further.

Read More
Joey S -
Sears Technician
September 07, 2011
A:

Checked my model and serial number against the ge recall website and the phone number you listed and the GSD3200 G00CC is not part of the recall. Checked the timer with a tester and it came back 3500 OHM. Any other ideas?

Read More
Anonymous -
September 07, 2011
A:

Anonymous: Your symptom could be caused by a faulty wire connection at the timer or at the push button selector switch. It could also have a faulty push button switch. Your dishwasher should have a technical data sheet located in an envelope under the tub of the dishwasher or inside the console. The tech sheet will show which contact should be closed based on which button is pushed. I recommend checking for loose or burnt or darken wires at the selector switch. If you can't locate the technical data sheet let me know and I can add an image of the tech sheet. NOTE: Be sure to disconnect the power supply before checking for loose wires and before testing the push button switch operation with an ohm meter.

Read More
Joey S -
Sears Technician
September 07, 2011
A:

Thanks for the information. I actually did check and the wires looked good, connections good, OHM tested good on the push button selector. OHM tested good on the timer too, supposed to be 1K to 3500K and it was 3500K. I did notice the other night pressing the hot dry vs not hot dry did have an effect on getting the water to start flowing. So despite the readings there may still be a problem. I also noticed the celluloid that moves up an down to hold release water - that piece is actually leaking when the tank empties about 2 ounces of water. It is leaking straight from the celluloid and the whole thing gets wet. It it rusted out and having a difficult time moving up and down. I greased it and its moving much better but obviously that whole part need replaced. Hopefully replacing that part will stop my leak, but I still seem to have a switch problem. I'm hesitant to throw money at this thing with multiple defects. Advice on that?

Read More
Mike -
September 07, 2011
A:

Mike: Based on your symptoms and findings you would likely be better off replacing the dishwasher rather than investing any money into it. It does sound like you have a faulty push button switch and the water leak may require a new pump and motor assembly.

Read More
Joey S -
Sears Technician
September 07, 2011
A:

Thanks for the help. Sounds like good advice - a new dishwasher.

Read More
Mike -
September 08, 2011
See more answers

Top Parts