Model #GMC305PDQ2 WHIRLPOOL Built-In Oven, Electric with Microwave

  • Oven
    3 Results
  • Control Panel
    3 Results
  • Oven Door
    3 Results
  • Latch
    3 Results
  • Internal Oven
    3 Results
  • Cabinet And Stirrer
    3 Results
  • Microwave Compartment
    3 Results
  • Microwave Door
    3 Results
  • Top Venting
    3 Results
Find part by diagram >

Error Codes

Error Code:



Question and Answers


Remove and reinstall M/wave door GMC305PDQ2


Thank you for contacting with your questions about your Whirlpool microwave. I am so sorry the door bracket needs to be replaced. In this case I recommend you have the microwave repaired by a qualified technician. 

We do not give repair information on microwave ovens because they are inherently dangerous to service. Microwaves contain high voltage internal components that can retain a lethal electrical charge even when the microwave is unplugged from the power supply. You need special equipment to work on a microwave starting with an anti-static wrist strap grounded to the microwave to even test components in it. Even minor door repairs and adjustments can cause microwave leakage, and a microwave shielding leakage test MUST be performed using a survey meter after ANY/ALL microwave service. 

For these safety reasons I strongly recommend having this repair completed by a qualified service technician. You can schedule service online at or by calling 1-800-4-MY-HOME (1-800-469-4663). Here at we love to help you with your repairs, but our expert advice is that microwaves are just too dangerous for a do-it-yourself project. 

Thank you for your understanding in this matter and I hope we can help you with any other questions and repairs in the future. Thank you for choosing Sears.


Read More
Rachel Morgan -
Sears Technician
October 08, 2014

Oven lock/self clean GMC305PDQ2 Whirlpool Electric oven/mw combo


Hello glad to help.  Thank You for choosing Sears
I am sorry and do understand your frustration when there is trouble with the oven.
Glad to help out.   Im  looking at your Kenmore Electric Oven model number GMC305PDQ2.

Here is whaT the E1.F5 says accordingly with the technical manual.  SELF-CLEAN TEMPERATURE 288 celcius (550 fairenheit)  not reached with-in the 45 minutes.


1.  Check the self clean latch assembly:  Latch arm pivot joint, arm/solenoid connection, solenoid spring, and spring washer.

2.  Check the Latch Solenoid:
     A.  Check the firm electrical connections.
     B.  Disconnect the two wires from the solenoid and measure the    
           resistance of the solenoid.  A small resistance (approx. 175
          ohms) is normal.  If the solenoid is open or shorted, it should
          be replaced.

3.  Check the latch switch.  Disconnect it and use a continuity tester
     A.  Door latched = switch closed, continuity should read 0 ohm
    B.  Door unlatched= switch open, continuity should read 0ohm

4.  Check door open/closed switch.  Disconnect it and use a continuity tester:  
     A.  Door open=switch closed,   continuity should read 0 ohms
     B.  Door closed=switch open, continuity should read 0 ohms

5.  Check power and element connections.

I hope this answers your questions but if you need further assistance please resubit another question with additional details.

Read More
Larry L -
Sears Technician
February 28, 2014

Whirlpool Oven reads hot but dosnt turn on


With the holidays up on us, its no time to have problems with the Whirlpool oven. Manage my life has been asked a similar question and the answer in the link provided below. Hope this information is useful while waiting for an expert response on your specific model. If this is not a repair you want to attempt, the link for service is also available.

Read More
Anna T -
December 26, 2012

That E2 F3 error code indicates that the electronic control board detects a high temperature in the oven that is out of range. Since the temperature sensor is okay, you could have a wiring failure in that sensor circuit or a failed electronic oven control board that is causing this problem. Since this unit is a microwave/oven combo, I recommend that you have a service technician diagnose and repair the oven. The microwave component makes this appliance dangerous to repair on your own. Microwaves contain high-voltage components that can retain a lethal electrical charge of up to 2200 VAC -- even when the microwave is unplugged. Repairs and adjustments, even minor ones such as replacing the control board, can cause microwave leakage. A microwave shielding leakage test should be performed after any microwave service. It is for these safety reasons that we are unable to guide you in microwave/oven repairs and instead recommend scheduling service with a qualified service technician. You can schedule service online with Sears Home Services or by calling 1-800-4-MY-HOME. We thank you for your understanding in this matter and hope we can help you with other questions and repairs in the future.

Read More
Lyle W -
Sears Technician
December 27, 2012
See more answers

Top Parts