Model #GLWS1349AS1 FRIGIDAIRE Residential Washers

  • Wshr Cab,top
    3 Results
  • Wshr Mtr,hose
    3 Results
  • Transmission
    3 Results
  • Control Panel
    3 Results
  • 134125200 Wiring Diagram
    3 Results
Find part by diagram >

Error Codes

Error Code:

Condition:

Check/Repair:

Question and Answers

Q:

My Frigidaire washer will not agitate in both directions.

A:

One way agitation in the washer would be a concern. I did some research on the unit and I was unable to locate information that would be helpful with regards to your question at this time. Your expert will answer within 24-48 hours with detailed information. If you do decide to schedule service and have a qualified technician help you, I have also attached a link to Searshomeservices.com. Thank you for using Manage My Life.

Read More
Barbara H. -
January 15, 2012
A:

Thank you for your question and I understand your concern.

If you loosen or take the belt off I must assume the motor will run normally in both directions.

If you can't rotate the transmission pulley in both directions I would have to suspect a faulty gear case assembly.

If you're planning on replacing the gear case rather than the washer; I recommend calling a service technician to perform the procedure.

If you do not feel confident repairing this problem yourself, then you can have it repaired at your home by a Sears technician. Here is a link for the website: Sears Home Services .

Read More
Joey S -
Sears Technician
January 17, 2012
A:

My washer will not agitate. It will fill up and spin but will not agitate. I unplugped the washer to try and reset and when i did i started the washer. Once it filled up and it started to agitate for a couple of minutes then it stopped. It will go through the process as if it was working properly but will not agitate. I took of the agitator and placed it back on but dont know what the problem really is.

Read More
cosaundra -
July 24, 2013
A:

Cosaundra; In order to provide any model specific information, I will need to know the model number of your washer. Also, if you let the motor cool down for a few minutes after it quits agitating, will it run and agitate again for a few minutes?

Read More
Joey S -
Sears Technician
July 24, 2013
A:

GLWS1349AS1 / WILL NOT DO ANYTHING NOW BUT FILL AND SPIN

Read More
cosaundra -
July 24, 2013
A:

Consaundra: You said it agitated for a couple of minutes the last time you unplugged and then reconnected the power cord. So, now it will drain and spin and fill but will not start and run in order to agitate. If this is correct, it could have timer failure or water level pressure switch failure. This type of symptom should be diagnosed and repair by a service technician.

Read More
Joey S -
Sears Technician
July 24, 2013
See more answers
Q:

Washer tub not functioning correctly

A:

It can be very frustrating when your washer begins to malfunction and not work properly. I did some research and provided a link to a similar question and answer on our site. I hope this will shed a little more light on the issue until the Expert responds to your question in more detail within 24 to 48 hours.

Read More
Julio -
November 24, 2012
A:

From the description you give I suspect the brake has failed and the transmission will need to be replaced to fix this problem. If the washer is agitating and spinning at the same time then the brake/transmission will need to be replaced. Replacing the transmission would be an above average do-it-yourself project. The transmission would cost approximately $166 dollars. Replacement might be a better option. I would suggest you check the holiday ads and see what is available. If you do not feel confident repairing this problem yourself, then you can have it repaired at your home by a Sears technician. Here is a link for the website: Sears Home Services . I can provide some do-it-yourself information if you have a few basic tools and feel comfortable doing such a repair. I hope this helps. You can reply with any additional details for further assistance.

Read More
Fred M -
Sears Technician
November 26, 2012
A:

Thank ya Fred for the info. Didn`t know the trans had a brake. That`s why I thought it might of been the spin bearing. Guess I`ll be findin another washer. Thanks again. Dan

Read More
Dan -
November 27, 2012
A:

Good hunting. Now is a good time of year to be shopping with all the sales. Keep in mind some of the newer evergy efficient models can seem pricey but they will actually pay for themselves over timer. My personal favorite new feature is a front load washer with direct drive. This means no belt and fewer bearing problems. If you get a washer from Sears be sure to join the ShopMyWay community. The Reward points are an excellent way to say money.

Read More
Fred M -
Sears Technician
November 28, 2012
See more answers
Q:

Is the timer on my Frigidaire washer the cause of the tub overfilling with water on the wash cycle only?

A:

The details that you describe are unusual. If you are stopping the fill by shutting off the water faucets in the back of the washer, then you could have a stuck hot inlet water valve on this washer. Except in the WARM/WARM setting, the hot water valve is not used in the rinse cycle. This could explain the difference in the wash and the rinse cycle if you are not turning on the hot water supply faucet when using the washer in the rinse cycle.

The water level pressure switch will normally stop the fill by opening a contact to shut off voltage to the water fill valves. If the pressure switch is stuck, the washer will continue to fill.

Your failure is likely in the water inlet fill valves or the water level pressure switch. A timer problem would not normally cause the washer to overfill.

If you need more help with this problem, resubmit your question with additional details.

Read More
Lyle W -
Sears Technician
November 02, 2009

Top Parts