Model #GLTR1670AS0 FRIGIDAIRE Residential Washers

  • Control Panel
    3 Results
  • Wshr Cab,door
    3 Results
  • Wshr Tub,motor
    3 Results
  • 134052900 Wiring Diagram
    3 Results
Find part by diagram >

Error Codes

Error Code:

Condition:

Check/Repair:

Question and Answers

Q:

Oil/Grease pattern on clothes GLTR1670AS0 Frigidaire Washer

A:

Thanks for your question- we see that no one from the community responded.  If you still require assistance on this topic, please resubmit your question with any updated information and we will have one of our experts take a look.  Also, we have updated our site to include information regarding common repairs and diagnosis, which can be found here: www.searspartsdirect.com/repair-help.html.  If you are looking for your owner’s manual, it can be found here: http://www.searspartsdirect.com/partsdirect/user-manuals.  Thanks for visiting SearsPartsDirect.com.

Read More
Natasha12 -
Sears Technician
May 13, 2014
Q:

Fridgidaire modle GLTR1670ASO front loader. Will not run or spin. Pump works.

A:

Having a properly working washer is very important. I found some information for you that I am hoping will help you until your expert answers your question. I added the link below to assist you. It may take two business days for your expert to respond. I do hope that everything works out on the washer.

Read More
Marc -
February 19, 2013
A:

Hello Marv. I am sorry to hear that you are having problems with that Frigidaire Front Load Washer Model GLTR1670AS0.

That model has a timer so it will not blink the console lights when it encounters a problem like other models that have an electronic control board in the console. It does have a motor control board in the bottom of the washer next to the drive motor. You seem to be indicating that the drive motor will not run in the tumble mode or the spin mode. This problem could be caused by a bad motor control board, a wiring failure, a bad timer or a failed drive motor. A technician will normally need to conduct some live voltage checks to determine the exact cause of your failure.

If you want to perform some preliminary checks, I recommend that you unplug the washer and check the wiring connections on the timer and the motor control board. Check the wire harness connections on the drive motor. You can remove the back panel of the console to access the timer wiring connections. The back panel will need to be removed to access the motor control board and the drive motor. I posted an image below that shows how to access the motor control board on a similar model of washer. Your exact model will be slightly different than the one shown below but the access procedure is basically the same.

If you find no wiring connection problems, you can pull the motor control board out and check it for burnt spots. If that motor control board is apparently bad, then it will need to be replaced. You can order that part from this page: Fridgidaire Washer GLTR1670AS0 Motor Controller 134149220.  Be sure that you unplug the washer before accessing internal components and replacing parts.

If need more help, reply with additional details and we will assist you further.

 

If you get to the point where you need to have a service technician diagnose and repair this failure, you can schedule service through this link: Sears Home Services Washer Repair. 

Read More
Lyle W -
Sears Technician
February 21, 2013
A:

Thanks for the direction. I took the motor control board out and cleaned it off. Dust ,etc. Put it all back together and it worked. Ran 4 loads and it is back to not spinning again. Maybe a bad connecting plug? What do you think?

Read More
Marv -
February 26, 2013
A:

There is a chance that you have a bad wire harness or a corroded connection plug. You can UNPLUG the washer and check the wire harness connections between the timer and the motor control board. Also check the connections between the motor control board and the drive motor. If those connections are corroded, you can clean them with electronic parts cleaner. That may help with a wire harness connection problem. If you still have the same problems after checking that issue, then you may need to replace that motor control board or the timer. Let us know if you need more help.

Read More
Lyle W -
Sears Technician
February 27, 2013
See more answers
Q:

No Bearing on This.

A:

Micheal - Nothing supports the front of the basket. When it is working correctly the drum is not supposed to rub the inside of the tub.

Support is supplied by two bearings in the rear section of the outer tub/drum, item 22 at the first link below. The bearings ans seal are not available separately from Frigidaire or Sears but are supplied as part of item 22. Should you be able to feel any clearance/play in the bearings then they are toast and should be replaced together with the seal.

In all likelyhood the small brass sleeve on the shaft of the spider is also likely in need of replacement. Should you be able to see or feel, with your finger nail any grooving of the sleeve where the seal lands then the sleeve needs to be replaced. Again you cannot obtain just the seal fron Frigidiare or Sears but have to purchase the entire basket assembly, item 16 in the first link below.

The second link below is to a site that claims to be able to supply bearings and seal for your machine. I have never used them so cannot comment any further. Substitute bearings are readily available from any reputable bearing supplier, the seals are the problem.

SKF, the bearing manufacturer, do supply a kit for a lining for the brass sleeve, details are available at:

http://www.skf.com/files/344136.pdf

again I have never used one so I cannot comment further. Should you elect to renew your bearings please do not do it like the guy in the second link below, a piece of wood on both races, this will bruise the balls and the races, only apply pressure to the outer race, nothing else, information on this at the following link may prove useful:

http://www.nationalprecision.com/bearing_basics.html

Please ley us know how you get on.

Good Luck.

Read More
biguggy -
June 29, 2012
A:

Micheal - Frigidair is totally owned by Electrolux I believe the manual availale at the link below may prove useful/informative. Good Luck

Read More
biguggy -
June 29, 2012
A:

The basket is supports by the spider support with three arms. This piece is part of the outer tub. The bearing is part of the rear outer tub half. If the front of the tub is dropping then the support arms or the bearing is at fault. The spider arms can come loose but the bearing is the most likely cause of the problem. The rear tub half will need to be replaced to fix this problem.

Read More
Fred M -
Sears Technician
July 01, 2012
See more answers

Top Parts