Model #GLGH1642DS1 FRIGIDAIRE Laundry Centers/Combos

  • Upper Cabinet/drum Heater
    3 Results
  • Motor/blower/belt
    3 Results
  • Control Panel
    3 Results
  • Lower Cabinet/top
    3 Results
  • Motor/tub
    3 Results
  • Wiring Diagram
    3 Results
  • Wiring Diagram
    3 Results
Find part by diagram >

Question and Answers

Q:

Washer won't start GLGH1642DS1 Frigidaire Laundry center

A:

Thank You for choosing Sears PartsDirect.com and being a valued member. It is unfortunate to hear that you are having issues with your washer and I do understand your frustration. Glad to help out. I'm looking at your model number glgh1642ds1 and from your description I suspect that you may have a damaged door strike or the door lock assembly is failing. Here is a link for a video that will help with the troubleshooting. I have included a link to our PartsDirect page where you can purchase the part you need to complete your repair. Just click the blue link above to be taken to the page. I trust this information will help you.

 

Thank you for choosing Sears PartsDirect.com.

 

SAFETY NOTICE: Be sure to disconnect power to the appliance before performing any repairs. If you are not comfortable with doing any voltage checks that might be recommended, please contact Sears for repairs. Be aware that there could be sharp edges inside the appliance that could cause cuts or other injuries to yourself or others.

Read More
Sherman_G_Wallace -
Sears Technician
October 07, 2014
Q:

frigidaire mod # glgh1642ds1

A:

A loud noise can really cause some concern and I am sorry for the inconvenience. I suggest you add to the thread of this question and include some more information such as what type of noise the dryer is making so that the expert can provide you with a more detailed answer. I did manage to find a link that will provide you with some good information. I hope this helps with your dryer troubles while you wait fro your expert response.

Read More
Joseph P. -
July 24, 2012
A:

That type of noise is often caused by a worn out rear bearing on the drum or a problem with the idler pulley. You could also have a worn drum glide on the front of the drum. Here is a link for a previous answer that shows how to open the dryer cabinet on that laundry center: How do I replace the rear bearing on my Kenmore dryer? . You can unplug the laundry center then remove the top dryer panel and manually spin the drum to determine the cause of that noise. If the noise is coming from the rear ball hitch bearing, then replacing that part should fix your problem. There is a kit for that rear bearing that has all of the parts that you need. The part number for that kit is 5303281153. Here is a direct link for that kit: Rear Bearing Kit for Frigidaire Laundry Center Model GLGH1642DS1 . Be sure that you unplug the laundry center before accessing internal components.

If the idler pulley is making the noise, then replacing that component should fix your problem. Here is a link where you can order that part: Frigidaire Laundry Center Model GLGH1642DS1 Parts .

If that front drum glide is making the noise, then that component will need to be replaced. You may need to replace the rear drum bearing and that front drum glide in that situation.

I hope that this information helps. If you need more assistance, reply with additional details.

If you get to the point where you need to have a service technician examine and repair the dryer, you can schedule service through this link: Sears Home Services .

Read More
Lyle W -
Sears Technician
July 26, 2012
See more answers
Q:

I have a Frigidaire Gallery Series Stackable Washer/Dryer

A:

I'm sorry to hear that you are having some difficulties with your washer, especially if it is not working properly. I did some research for you at Managemylife.com and found an expert answer to a similar question that may help until your expert can respond to your specific question. The link is attached below. If you do decide to schedule service and have a qualified technician help you, I have also attached a link to Searshomeservices.com. I hope these links provided assistance for you.

Read More
Joseph P. -
December 29, 2011
A:

Hi Shawn,

Thank you for submitting a question to Manage My Life.

This issue is most likely caused by a faulty motor control speed board. Yes, there is a motor control speed board part number 134149220. I am including the wiring diagram with no spin checks in the images below. The diagnosis of this issue will require the use of an ohm/volt meter and you will have to perform ohm checks and/or live voltage checks. If you have an ohm/volt meter and are confident in your technical abilities, please utilize the checks below. Working with live electrical current can be very hazardous and possibly deadly. Do not attempt these measurements without the proper tools and safeguards. If you are not already sure you can perform these checks safely and competently, refer this work to a qualified professional.

If you do not feel confident repairing this problem yourself, then you can have it repaired at your home by a Sears technician. Here is a link for the website: Sears Home Services .

Here is a link that you may use to view the parts list diagram or to purchase any parts needed; Sears Parts Direct .

I hope this is helpful. If I may be of further assistance please reply to this post.

Landell

Read More
Landell -
Sears Technician
December 30, 2011
A:

Ok Landell, thank you for the quick response.. My brother feels confident in making the repair.. I myself have carpenter skills but I don't mess with live electric.. My only other question is, can this be accessed from the front of the washer or do we have to access from the backside?

Read More
Shawn -
January 01, 2012
A:

Shawn, The motor control is located in the back of the washer on the right hand side. You will need to access it by removing the back panel. If I may be of further assistance please reply to this post. Landell

Read More
Landell -
Sears Technician
January 03, 2012
See more answers

Top Parts