Model #GLD4500N10BB GE Dishwasher

  • Escutcheon & Door Assembly
    3 Results
  • Body Parts
    3 Results
  • Upper Rack Assembly
    3 Results
  • Lower Rack Assembly
    3 Results
  • Motor-pump Mechanism
    3 Results
Find part by diagram >

Troubleshooting

Error Codes

Error Code:

Condition:

Check/Repair:

Question and Answers

Q:

remove ge dishwasher built in power cord GLD4500N10BB Ge Dishwasher

A:

Page 12 in your Installation Guide shows how to connect the wires directly to the house power supply for the dishwasher. The like wires will need to be connected together (black to black, white to white and green to green). 

If you need more help, let us know.

Thanks for choosing Sears PartsDirect.

Read More
Lyle W -
Sears Technician
June 02, 2014
Q:

Recessed spring for door handle GLD4500N10BB Ge Dishwasher

A:

Thank You for choosing Sears PartsDirect.com. I regret to hear that you are having issues with your dishwasher and do understand your frustration. Glad to help out. Im looking at your model number GLD4500N10BB and the repair requires steady hands. I have included a video that will help you do the repair and good luck. Just click the blue link above to be taken to the page. If you have further questions please resubmit your question for further information. 
 
Thank you for choosing Sears PartsDirect.com.

Read More
Sherman_G_Wallace -
Sears Technician
April 15, 2014
Q:

GE Dishwasherhttp://www.managemylife.com/mmh/questions/224619

A:

I can see it would be frustrating not to have the convenience of your dishwasher. While your waiting on an expert response you can visit the SearsHomeServices website to schedule service. I have provided the link below. I hope thsi helps!

Read More
Jacqueline S -
October 01, 2010
A:

The board is a possibility but one thing to realize is that this particular dishwasher has a circulation pump motor and a separate drain motor.

From the description you give the dishwasher will fill and drain but the circulation motor is not working.

If you wish to do-it-yourself then I's suggest you start with the images below. The first shows how to run a diagnostic test. The 2nd shows the wiring diagram and may be helpful to you.

The problem can be a loose connection at the circulation motor.

The WD21X10247 main control is about $133 dollars while a new motor WD26X10033 is closer to $179 dollars.

Try the test first and reply with any additional details or questions for further assistance.

Remember to turn the power off before checking any connections.

Read More
Fred M -
Sears Technician
October 02, 2010
A:

Thanks for the speedy response>) ok, I ran the service mode:- main pump test the dishwasher just sits there and hums auxillary pump test I hear it working detergent/rinse aid module test it just sits there all quiet (not quite sure what im supposed to hear), water valve test - water is heard filling up dishwasher Heater test is quiet, assuming this is working as intended. Ok so it sounds like a main pump problem? yay what a way to spend my weekend, any other tips / tests / advice before I weigh up the cost of repair versus just buying a new dishwasher.. Sucks this is only 18 months old and was pre-installed with our new home.

Read More
MarkBM -
October 02, 2010
A:

hmm I did format the above response, but it condensed it when I replied, sorry if its hard to read now >(

Read More
MarkBM -
October 02, 2010
A:

The motor hangs by a bracket and a hose clamp. You'll want to pull the dishwasher out to get a good look. Before spending the motor on a new motor I'd suggest you go ahead and access and pull the motor off. It may be a toothpick or bone or something jamming it. it's worth a short. If you get it off without any problems and find nothing you'll be a little more confident spending the motor on the motor. I'll be off till Tuesday just to let you know.

Read More
Fred M -
Sears Technician
October 02, 2010
A:

This comment is a little late but I wanted to share my experience how I fixed my problems which had the same symptoms that Mark was experiencing. Water would fill, wash cycle should have started but after it times out it would drain. It would fill again suppose to go through the rinse cycles but nothing. After some time would pass it would drain again. I checked the door switch it was responsive. Checked the resistance on the relays and they appeared good. So here I am, I ruled out electrical problems. So as Fred had suggested I removed the motor which had the pump mechanism attached. It looked clean and didn't appear to be jammed. However I looked at the filter inside this rubber shroud and I see the plastic filter. There is this gooey stuff jammed in all the holes which isn't allowing water to pass. Attached to this rubber shroud is something that looks like a flow control switch. No water, no flow, no pump. I did have one concern about some of the rubber pieces. Some of the rubber was starting to peel off in layers and I wasn't sure if that is something that I should replace or not.

Read More
Richard Berndt -
March 01, 2011
See more answers

Top Parts