Model #GHW9300PW0 WHIRLPOOL Residential Washers

  • Top And Cabinet Parts
    3 Results
  • Door And Latch Parts
    3 Results
  • Control Panel Parts
    3 Results
  • Dispenser Parts
    3 Results
  • Tub And Basket Parts
    3 Results
  • Pump And Motor Parts, Optional Parts (not Included)
    3 Results
  • Pedestal Parts (not Included)
    3 Results
Find part by diagram >

Error Codes

Error Code:

Condition:

Check/Repair:

Question and Answers

Q:

How to remove the control panel. GHW9300PW0

A:

Thank You for choosing Sears PartsDirect.com and being a valued member. It is unfortunate to hear that you are having issues with your washer and I do understand your frustration. Glad to help out. I'm looking at your model number GHW9300PW0 and here is a link for a video that may help with the disassembly. Just click the blue link above to be taken to the page. I trust this information will help you.

 

Thank you for choosing Sears PartsDirect.com.

 

SAFETY NOTICE: Be sure to disconnect power to the appliance before performing any repairs. If you are not comfortable with doing any voltage checks that might be recommended, please contact Sears for repairs. Be aware that there could be sharp edges inside the appliance that could cause cuts or other injuries to yourself or others.

Read More
Sherman_G_Wallace -
Sears Technician
January 06, 2015
Q:

We are having trouble restarting our Whirlpool washer that my daughter paused.

A:

Good morning.... Yes, unplugging it for 10 minutes would reboot the circuitry back to it's factory settings. It would be very helpful if you could include your full model number. I did locate a link that will discuss this situation in greater detail. Keep in mind that an expert will be responding within the next two business days if not sooner and will likely offer you more information and instruction. I hope this link will help guide you as to what might wrong with your washer and have a nice day

Read More
Henry -
December 28, 2012
A:

Hi,

Thank you for asking this question and allow me to answer it this way.

Correct, the thing you need to try is to disconnect the washer from the wall and let it set for 5 minutes and reconnect and see if the control has unlocked. I have considered the fact it might be in a demo mode. But the actions of the washer is different than what you have described.

How to activate the Control Panel Sales Demo Mode? 1. Power must be off. 2. The following steps must be performed within 5 seconds: a) Select the Water Temp Option b) Select the Soil Level Option c) Select the Water Temp Option d) Select the Soil Level Option. 3. The Control Lockout indicator will blink red while the unit is in the demonstration mode. 4. To exit the Demo, turn off the machine and then turn it back on and repeat the entry steps, or simply unplug the machine for 30 seconds. 5. To reset and repeat the Demo, open and close the door.

I hope this answer is useful and that it helps you correct the problem with your appliance.

Read More
Bill__W -
Sears Technician
December 28, 2012
See more answers
Q:

Problem codes

A:

Error codes are meant to be diagnostic but many of them are not explained in the owner's manual. I located a previous expert post with answers for your model and attached below. Hope this helps.

Read More
Barbara H. -
April 22, 2011
A:

The dL code indicates a problem with the door lock assembly.

Are you having problems with the door locking?

If there is a door lock problem then most likely the washer will not spin.

The images below will help you remove the top and how to access the door switch assembly.

The 8182634 door latch can be obtained from the following link: Sears PartsDirect .

You can reply with any additional details or questions for further assistance.

Read More
Fred M -
Sears Technician
April 23, 2011
A:

Once I push and hold the control button, the lock solenoid does not engage, and that is when the dl code flashes. After have checked the wire connections for loose wires , how can I tell if it is not the Control Panel itself, versus the Door Lock?

Read More
Karen -
April 23, 2011
A:

The majority of the time the problem will be with the door lock assembly. To confirm this will require checking live voltage. This is difficult to do and I would suggest a technician fix this problem.

Read More
Fred M -
Sears Technician
April 25, 2011
See more answers

Top Parts