Model #GGW9250PL0 WHIRLPOOL Residential Dryer

  • Top And Console Parts
    3 Results
  • Cabinet Parts
    3 Results
  • Bulkhead Parts
    3 Results
  • 8318276 Burner Assembly
    3 Results
  • Door Parts
    3 Results
  • Pedestal Parts (not Included), Optional Parts (not Inc
    3 Results
Find part by diagram >

Error Codes

Error Code:

Condition:

Check/Repair:

Question and Answers

Q:

Thermal fuse and thermistor testing GGW9250PL0 Whirlpool Residential dryer

A:

Searspartsdirect.com is always a great resource to find the answers to your parts questions. Your Sears partsdirect expert will research your question and respond within two business days but usually sooner. Thank you for using Searspartsdirect.com!

Read More
Yadira B -
June 04, 2013
A:

Thank you for your question and I understand your concern.

When checking the thermal fuse and thermistor for continuity and Ohm's resistance; disconnect the two wires from the components before measuring continuity and resistance.  A power outage would not generally cause the thermal fuse or thermistor to fail. If the dryer is overheating due to a restricted vent system, a faulty or bad connection in the thermistor circuit or a stuck heater relay contact on the control board it could cause the thermal fuse to fail. 

Remove and replace the thermal fuse part # 3392519 and then disconnect the thermistor and re-check the resistance. The thermistor should measure approximately 10 Ohms at room temperature. Generally speaking, if the thermistor was open or shorted, the control would display an E1 or E2 error code in the display window. The thermistor is likely Okay if it's not displaying an E1 or E2 error code.

After replacing the thermal fuse, remove the vent hose from the back of the dryer and monitor the exhaust temperature with a thermometer. On high heat, the exhaust temperature should average 155 degrees plus or minus 10 degrees.  If the exhaust temperature continues to rise above 170 and keeps rising, I would suspect the heater relay contact on the control board is stuck or welded shut. If the temperature is averaging 155, then the venting system or vent hose is pinched or restricted. Check the vent cap outside too where the dryer vents outside and make sure the flapper door is opening.

 I hope this is helpful. If I may be of further assistance as more details become available, please reply to this post.


Read More
Joey S -
Sears Technician
June 07, 2013
See more answers
Q:

dryer model# ggw9250plo display faint and does not reset by pushing " more / less " I was able to reset once but it will not reset anymore.

A:

When it comes to locating parts for your appliance Sears Parts Direct website is the place to visit. I have attached the link below so you can speak with a Sears associate to find out what part is needed. Have a nice day!

Read More
Dezeray -
April 25, 2012
A:

You could have a wiring problem, a bad main machine control board or a problem with that user interface control board that could be causing this problem. That part number that you provided in the details does not appear to be valid. I can't tell which part that you replaced using that information.

I recommend that you unplug the dryer and check the wiring connections on the main machine control board. The wiring diagram for your dryer is shown in the image below. The second image provides some information for accessing the control board and those connections. Check the black and white wires that are traced in that wiring diagram. Also, I recommend that you check the user interface wire harness connections. If all of those connections are okay, then you could have a short in one of those loads that are connected to the control board. That could be dragging down that DC voltage to the user interface control board. This may help you resolve that problem. If you need more help, reply with additional details and we will assist you further.

If you need parts, you can order them from this page: Whirlpool Dryer GGW9250PL0 Parts .

If you get to the point where you need to have a service technician diagnose and repair this failure, you can schedule service through this link: Sears Home Services .

Read More
Lyle W -
Sears Technician
April 26, 2012
See more answers

Top Parts