Model #GBD307PRB00 WHIRLPOOL Built-In Oven, Electric

  • Lower Oven Parts
    3 Results
  • Upper Oven Parts
    3 Results
  • Oven Door Parts
    3 Results
  • Latch Parts
    3 Results
  • Internal Oven Parts
    3 Results
  • Control Panel Parts
    3 Results
  • Top Venting Parts, Optional Parts
    3 Results
Find part by diagram >

Error Codes

Error Code:

Condition:

Check/Repair:

Question and Answers

Q:

Whirlpool double oven

A:

I apologize, to hear that you're having this problem with your oven. I have done some research and located a link similar to your question that may be helpful until an Expert responds. Hope this helps and thank you for using Manage My Life!

Read More
Carmen G -
August 29, 2012
A:

Thank you for your question and I understand your concern.

If you're able to program and start the ovens but neither one will heat, then the oven may not be getting the proper voltage supply. If the oven lost the line two (L2) voltage supply, the oven elements will not heat. Locate the house circuit breakers dedicated for the oven and reset both circuit breakers by flipping the two breakers off and on 2-3 times and then see if the oven will heat. You will need to reset the clock on the range before programming the upper and lower oven for bake. The oven must have 220 volts in order for the oven elements to heat. If the oven is getting the proper voltage (220) and if only one of the two ovens will not heat then it could have faulty oven shut down thermal fuse. I added an image below showing the location of the shut down thermal fuses. Each oven has a shut down thermal fuse. The fuse can be disconnected and tested for continuity with an Ohm meter. If the fuse does not measure continuity, it is faulty and will need to be replaced. NOTE: Disconnect the power supply from the oven before servicing. I hope this is helpful. If I may be of further assistance as more details become available, please reply to this post. I recommend calling a service technician to diagnose and repair your oven.

If you do not feel confident repairing this problem yourself, then you can have it repaired at your home by a Sears technician. Here is a link for the website: Sears Home Services .

Read More
Joey S -
Sears Technician
August 30, 2012
A:

Nothing in the oven works, except the light, and the panel beeps when touched. So, how do I know it is the L2 voltage supply. I did reset the breaker switches with not luck.

Read More
charles -
September 10, 2012
A:

Charles: It will require a voltage meter in order to measure and confirm the voltage supply. At the back of the range where the power cord is attached is a terminal block. The voltage must measure 220-240 volts when measuring voltage across the outside terminals. It should measure 110-120 volts when measuring across the center terminal to each outside terminals. If 220-240 volts is measured, I suspect the oven shut down thermal has tripped open.

Read More
Joey S -
Sears Technician
September 10, 2012
A:

how often is that the case when the panel is out?

Read More
charles -
September 10, 2012
A:

Charles: It's not that uncommon to have a voltage supply issue, faulty oven control board or a tripped thermal shut down switch.

Read More
Joey S -
Sears Technician
September 11, 2012
A:

Joey - Attached is a pic of what i think is the power tranformer, there are four leads coming from it, two red on top and two blue on bottom. Testing the two leads on the left, the top red and bottom blue I get a reading of 110/115 volts, testing the right two the same way, i get NO reading, is this the problem? Thank you.

Read More
charles -
September 12, 2012
A:

Charles: The voltage should measure 110/120 across the two red wires and it should measure 23 volts AC across the two blue wires. See images below.

Read More
Joey S -
Sears Technician
September 13, 2012
A:

good morning - Sorry this is taking long. Okay, I have tested the black and red terminals coming into the oven, they are okay at 220. I did test the red terminals across the power transformer they are at 110 and the blue wires test at 23. I am now looking at the control power thermal fuse from behind the panel, could this be the problem, if so, I cannot disconect only at one end? Picture below. Also, i did test the leads to the Oven Shutdown Thermal fuse on the back panel, no power? Thanks for all your help.

Read More
charles -
September 13, 2012
A:

Charles: If the transformer is getting 110 across the two red wires at the transformer, the inline control thermal fuse is Okay. If the control panel will power up and your able to program the oven and it does not heat, you will need to check the oven shut down thermal fuse on the back of the range. See images in the previous response.

Read More
Joey S -
Sears Technician
September 13, 2012
See more answers

Top Parts