Model #GBD307PDS09 WHIRLPOOL Built-In Oven, Electric

  • Lower Oven Parts
    3 Results
  • Upper Oven Parts
    3 Results
  • Oven Door Parts
    3 Results
  • Latch Parts
    3 Results
  • Internal Oven Parts
    3 Results
  • Control Panel Parts
    3 Results
  • Top Venting Parts, Optional Parts
    3 Results
Find part by diagram >

Error Codes

Error Code:

Condition:

Check/Repair:

Question and Answers

Q:

Blower Fan not coming on GBD307PDS09 Whirlpool Built in oven - electric

A:

No one knows?

Read More
Michael -
October 28, 2015
Q:

I replaced the heating element on a whirlpool built in electric oven but the new element does not work. Are there other parts that tipically go bad?

A:

I'm sorry about the difficulties your still having with the build in oven. I did some research based on your question & added the link below. An expert will also respond with additional information. Hope this is helpful.

Read More
Yadira B -
November 19, 2012
A:

You could have blown oven shut-down thermal fuse in that circuit. The wiring diagram in the first image below shows that component circled in red for the upper oven. The lower oven has a similar fuse. The physical location of those fuses is shown in the second image. You would need to shut off the house circuit breakers for the oven and pull it out of the cabinet to access those fuses. They are located on the outside back wall of the oven cavity. Remove the outer back panel on the oven to access that component. If those fuses are okay, then you could have a bad relay on the electronic oven control board. The relays are circled in green and blue. The location of that control board is in the console. It is mounted behind the control panel. A wiring failure in that circuit could also prevent the element from heating.

You can order parts from this page: Whirlpool Oven Model GBD307PDS09 Parts . Be sure that you shut off the house circuit breakers for the oven before accessing internal components and replacing parts.

I hope that this information helps. If you need more assistance, reply with additional details.

If you get to the point where you need to have a service technician diagnose and repair this failure, you can schedule service through this link: Sears Home Services .

Read More
Lyle W -
Sears Technician
November 20, 2012
See more answers
Q:

Control panel for Whirlpool Gold double oven

A:

Having to keep on replacing parts after parts can be really frustrating especially when it starts to get really expensive. While you are waiting on an expert to answer your question, a suggestion I have is to visit Sears Home Services website to set service with a Sears technician so they can diagnose everything and get this problem fix. I have attached the link below. Hope this helps!

Read More
Dezeray S -
May 16, 2011
A:

This problem could be caused by a damaged electronic control board (part 8302152). You could also have a problem with the power transformer (part 9760587).

The control board behind the console has the digital display. This board can be damaged when you have a short in the element that you described in your details. You can shut off the house circuit breaker for the oven and check the wiring connections between the power transformer and that control board. The first image below shows those wiring connections on a diagram. The second image shows a parts diagram. You should be able to access the back of the control panel and the transformer by carefully pulling the oven out of the cabinet and removing the top panel (with the circuit breaker shut off ). The second image shows a parts diagram of the oven. You should be able to access those components by removing the top panel over the control (KEY 18). The power transformer is KEY 6 in the top group of parts. The electronic oven control board is KEY 3 in the bottom group of parts.

If you find a loose wire between the control board and the transformer, correcting that problem may fix the dim display. If you find no problems with the wiring connections, you may consider checking the DC voltage on the blue wires coming out of that power transformer. That is a 24 volt transformer. If you carefully power the oven up and check that DC voltage on the blue wires using a volt/ohm meter, you should measure at least 23 volts DC. If not, then that power transformer needs to be replaced. NOTE: Use extreme caution when making this type of live voltage check with the internal oven components exposed. Shut off the circuit breaker as soon as this test is completed. Avoid contacting any bare metal wiring contacts during this test. If you are not completely confident that you can safely conduct this live voltage check, I recommend that you have a service technician repair the oven . Here is a link for the Sears Service website in case you need it: Sears Home Services .

If the power transformer is okay, then you will probably need to pull that control board out of the oven and have it repaired. The replacement part for that control board is no longer available. You can pull the control board out and send it to Core Centric Solutions for repair. Here is a link for that company's website: CoreCentricSolutions.com . The contact information is on that website. It costs about $150 to have the control board repaired. Once you receive it back from Core Centric Solutions, you can install it in the oven and test it.

This information may help you repair the dim display on your own. If you need more assistance, reply with additional details.

If you are not confident that you can repair this failure on your own, you can schedule service through the Sears Service link that I provided above.

Read More
Lyle W -
Sears Technician
May 18, 2011
See more answers

Top Parts