Model #FPUS2686LF0 FRIGIDAIRE Side-by-Side Refrigerator

  • Freezer Door
    3 Results
  • Refrigerator Door
    3 Results
  • Cabinet
    3 Results
  • Shelves
    3 Results
  • Controls
    3 Results
  • System
    3 Results
  • Ice & Water Dispenser
    3 Results
  • Ice Container
    3 Results
  • Ice Maker
    3 Results
  • Wiring Schematic
    3 Results
  • Wiring Diagram
    3 Results
Find part by diagram >

Error Codes

Error Code:

Condition:

Check/Repair:

Question and Answers

Q:

Replaced Water Filter, Next day won't dispense water FPUS2686LF0 Frigidaire Refrigerator

A:

Thank you for choosing Sears Parts Direct. I can certainly understand how frustrating it can be when your water will not work after replacing the filter on your refrigerator. I did look into the model number you have provided and I have found information to assist you. 

When replacing your water filter you should have turned off the icemaker. Once the filter is intalled you will need to purge the water system by trying to fill up a glass of water. It will take a little more than 5-10 minutes then it will start dispensing water. After water comes out of dispenser, then you turn the ice maker back on. 

You may need to purge the air out of the hose for it to work.

Let me know if this helps. You can also find the information on page 16 of your Owner's Manual. 


 
You can also visit searpartsdirect.com for parts, diagrams, and repair information.
 
 
If you do not feel confident repairing this problem yourself, then you can have it repaired at your home by a Sears technician. Here is a link for the website: Sears Home Services.

Thank you for your question. Have a great day. 

Read More
Natasha12 -
Sears Technician
May 05, 2014
Q:

FPUS2686LF0 Frig that stopped cooling FPUS2686LF0 Frigidaire Refrigerator

A:

Thank you for choosing SearsPartsDirect.com. I understand how frustrating it can be when the refrigerator stops cooling. The compressor should be making a humming noise and should be hot to the touch. If it is not running, the three components that could be bad are the compressor, starter or capacitor. We do not recommend for our customers to work on compressors themselves as it may cause more damage to the unit.
Make sure your controls are set correctly and that it is not in lock out mode. Try to unplug the unit for five minutes and reconnect. Wait another five minutes to touch any of the controls to make sure it has completely reset itself. Check your fuse box and flip the switch off as well when you do this to make sure it isn't your house fuse that has burnt out. I also recommend checking your door seals. You may test the gasket with the refrigerator plugged in if you choose. Open the door and place a piece of paper or dollar between the gasket and the refrigerator frame. Close the door and pull the paper. If there is resistance from tugging at the paper, there is no leak in that portion of the door. Repeat this process throughout the perimeter of the door. If you find an area where the paper easily pulls out, there is a gap in the gasket and it will need to be replaced.
SAFETY NOTICE: Be sure to disconnect power to the appliance before performing any repairs. If you are not comfortable with doing any voltage checks that might be recommended, please contact your local service provider for repairs. Be aware that there could be sharp edges inside the appliance that could cause cuts or other injuries to yourself or others.
If you do not feel confident repairing this problem yourself, then you can have it repaired at your home by a Sears technician. Here is a link for the website: Sears Home Services
If you have further questions please let me know. Thanks for using SearsPartsDirect.com.

Read More
Lokelani -
Sears Technician
October 07, 2013

Top Parts