Model #FGF379WECS FRIGIDAIRE Free Standing, Gas

  • Backguard
    3 Results
  • Burner
    3 Results
  • Body
    3 Results
  • Top/drawer
    3 Results
  • Door
    3 Results
  • Wiring Diagram
    3 Results
Find part by diagram >

Question and Answers

Q:

Can't read temp on digital readout FGF379WECS Frigidaire Range

A:

Hello glad to help.  Thank You for choosing Sears PartsDirect.com
 
I am sorry and do understand your frustration when there is problems with the range.
 
Glad to help out.   Im  looking at your Frigidaire Range model number FGF379WECS.

When you can't read the temperature readout then you need to first check for loose, bare, broken wires on the control board.   Check the ribbon wire from the control panel to the control board.   

If all wiring is good then you need to replace the control board.

Control board for the model 
FGF379WECS.


Please "RESUBMIT YOUR QUESTIONS IF THERE IS ANY OTHER PROBLEMS".

Thank you for your understanding in this matter and I hope we can help you with your future questions and repairs.  Thank you for choosing Sears and using our SearsPartsDirect.com.
 

Read More
Larry L -
Sears Technician
April 18, 2014
A:

How do I install the new part? Is there an online video somewhere? So far, I haven't found one. Thanks.

Read More
Phil -
September 30, 2014
See more answers
Q:

Frigidaire Gallery Professional Model # FGF379WECS - heating problem

A:

I'm sorry about the difficulties you're having with your range.  While you are waiting for an expert to respond I was able to locate some great information that could possibly assist you with your issue.  I have added the link (click here). Hope this helps!

Read More
Yadira B -
June 26, 2013
A:

Thank you for your question and I understand your concern.

Based on the symptom and details, I would suspect the bake glow bar igniter is on the verge of being too weak to keep the oven safety valve open. The bake glow bar igniter must pull enough current/amperage to open the oven safety valve and keep it open so gas can flow to the bake burner properly. The bake igniter for model FGF379WECS is part #5303935066 which can ordered from Searspartsdirect.com

The bake igniter can be accessed and replaced by removing the oven floor and the flame spreader. The igniter is located on the side of the bake burner.

Note: Disconnect the power cord from the power source before servicing. 

 

Read More
Joey S -
Sears Technician
June 26, 2013
A:

Thank you, Joey. That makes sense - we'll give it a try.

Read More
frank -
June 26, 2013
See more answers
Q:

im replacing the digital display on my frigidaire stove. need assistance

A:

When replacing a part on a range, Manage My Life is here to help. While you are waiting for your expert answer, I did manage to find a link that will provide you with some good information to help you with your quesiton. I hope my link is useful.

Read More
Joseph P. -
August 10, 2011
A:

The original clock has small shafts pushed into holes in it. The knobs push on the shafts. The shafts and knobs are replaceable parts. The knobs pull off the shafts and the shafts will pull out of the clock.

I use a pair of cotton gloves to pull the knobs off and if necessary a pair of pliers to pull the shafts out.

These knobs get brittle from heat over time and sometimes break when you pull on them. If this happens, you have to order new knobs or shafts to replace the ones that break.

The part number for the knobs is 316015102, and the price is $18.37 each. The part number for the shafts is 316080600, and the price is $8.42 each. Be careful as you remove them and you might not break any.

Read More
Jimmy K -
Sears Technician
August 11, 2011
See more answers

Top Parts