Model #FGB24L2ASA FRIGIDAIRE Wall Oven, Gas

  • Control Panel
    3 Results
  • Burner
    3 Results
  • Body
    3 Results
  • Door/drawer
    3 Results
  • Wiring Diagram
    3 Results
Find part by diagram >

Error Codes

Error Code:

Condition:

Check/Repair:

Question and Answers

Q:

frigidaire oven preheats then goes off

A:

Having a Range that is not working properly can be a great concern as well quite frustrating. I have taken the time to research on the Manage My Life website and have located similar information from what your experiencing. While you are waiting for a detailed reply from an expert I have attached the link below. Hope this helps!

Read More
Priscilla V -
January 16, 2012
A:

goes with my previous question on the frigidaire wall gas oven model number FGB24L2ASA also checked my broiler I turned it on it stayed on little while like it got so hot then it turned off also.

Read More
sandy -
January 16, 2012
A:

Thank you for your question and I understand your concern.

Based on your symptom and details it sounds like it may have a weak glow bar oven igniter. The glow bar igniter must come on and pull enough current/amperage to cause the oven gas valve to open. It may pull enough current when the oven is first turned on but after it glows red for some length of time it can become weak and not pull enough current to cause the gas valve to reopen whenever the oven control calls for heat. You can open the broiler drawer and see the glow bar igniter. If you find it glowing red for a minute or longer and the burner never ignites; replace the glow bar igniter and your oven should operate normally again.

The oven igniter is part #318177710 which can be ordered from Sears PartsDirect .

I hope this is helpful. If I may be of further assistance as more details become available, please reply to this post.

Read More
Joey S -
Sears Technician
January 18, 2012
See more answers
Q:

oven not heating up

A:

A non working Oven is not something any of us want to see. If you are technically handy, this is a good site to get instruction and fix some things yourself. If you do not feel confident doing your own repairs, an option is to visit Sears Home Services and use the scheduler. While you wait for the expert to review your model, you can check the bottom links for some possibilities. Hope this is of help.

Read More
Priscilla V -
September 26, 2011
A:

Thank you for your question and I understand your concern.

The electronic oven control/clock has most likely failed preventing the bake and broil elements from heating. The Electronic Oven Control (EOC) is part #316557511 which can be ordered from Sears PartsDirect .

The clock/oven control can be removed and replaced from the rear of the range by removing the panel from behind the console. NOTE: Disconnect the power cord from the power source before removing and replacing the clock/oven control. Pull one wire off at time from the old control and connected it to the corresponding terminal on the new control.

If you do not feel confident repairing this problem yourself, then you can have it repaired at your home by a Sears technician. Here is a link for the website: Sears Home Services .

Read More
Joey S -
Sears Technician
September 27, 2011
A:

Hello I have a frigidaire wall gas oven model number FGB24L2ASA ,it will preheat then shuts off it will come back on but later and it doesnt keep the temp you set it goes off and on .please any ideas out there? thought might be the thermostat?

Read More
sandy -
January 16, 2012
A:

Sandy: I would suspect a weak glow bar oven igniter. If it takes a long time for the oven gas valve to open once the oven igniter cycles on, replace the oven igniter.

Read More
Joey S -
Sears Technician
January 17, 2012
A:

Joey,thanks also my broiler goes off after it gets so hot then it goes out also.on the frigidaire oven.

Read More
sandy -
January 17, 2012
A:

Sandy: The bake and broil are the same burners. The broiler will shut off once it reaches maximum temperature. When broiling; you do preheat the oven or the burner will cycle off once it reaches maximum temperature.

Read More
Joey S -
Sears Technician
January 17, 2012
A:

Joey is there a way to check the glo bar igniter ?

Read More
sandy -
January 17, 2012
A:

Sandy: If it glows and takes a long time for the oven to ignite, the glow bar is weak and needs to be replaced. Or, if you have a clamp on amperage meter, you can clamp the meter around one of the wires connecting the glow bar igniter and check the amperage/current draw. To save and work, if it's glowing but takes a long time to ignite, replace the igniter located towards the back of the broiler compartment.

Read More
Joey S -
Sears Technician
January 17, 2012
A:

Ok thanks Joey appreciate it will get it checked out.thanks

Read More
sandy -
January 17, 2012
See more answers
Q:

Wall oven not turning on.

A:

The Oven is definitely something we depend on and when it begins to malfunction it can be a huge inconvenience. While you are waiting for an expert to respond, I have attached some helpful links below that may provide information to assist you with your question.

Read More
Priscilla V -
December 07, 2011
A:

You are probably hearing a relay that is clicking on that control board after you set the oven in the bake or broil mode. Your details seem to indicate that the igniter is glowing but the burner never lights. The theory of operation for the ignition system in this oven is shown in the image below. If the igniter glows but does not heat to a point where enough current flows to the safety gas valve to open it for ignition, then the burner will not light. If this describes your situation, then replacing that igniter should fix your problem. The part number for the igniter is 318177710. You can order it from the Sears PartsDirect website. Here is a direct link for that part: Igniter . Shut off the house circuit breaker for the oven (or remove the house fuse) to disconnect electrical power before accessing and replacing that igniter .

If the igniter does not glow, then you could have a bad igniter, a failed safety gas valve, a bad control board or a wiring failure in that ignition circuit.

There is chance that the gas line is clogged but this i not a common failure. A service technician would need to diagnose and repair that type of problem. Here is a link for the Sears Service website in case you need it: Sears Home Services .

If you need more help, reply with additional details and we will assist you further.

Read More
Lyle W -
Sears Technician
December 09, 2011
See more answers

Top Parts