Model #FGB24L2ABA FRIGIDAIRE Wall Oven, Gas

  • Control Panel
    3 Results
  • Burner
    3 Results
  • Body
    3 Results
  • Door/drawer
    3 Results
  • Wiring Diagram
    3 Results
Find part by diagram >

Error Codes

Error Code:

Condition:

Check/Repair:

Question and Answers

Q:

No power to flat glow bar pilot. FGB24L2ABA Frigidaire Gas oven

A:

Thanks for the inquiry and for being a valued member.

I am sorry to hear that the glow bar is not receiving power. I know how frustrating that is to have happen. 

There is not a fuse or reset switch for the unit. The failure could be the Electronic Oven Control, a broken wire, or a failed oven safety valve if voltage is not present at the igniter. Further testing with the meter would be needed to isolate the damaged component or wire. 

If you would feel more confident have a Sears Home Service technician help assist with the diagnosis/repair, you can call 1-800-469-4663, or click here to be directed to the page to set up service.

I hope this helps and thanks for using SearsPartsDirect.com. We appreciate your business. 

 

Read More
Jeff Wallace Sr -
Sears Technician
December 04, 2014
Q:

Hello, I have a Friidaire LP wall oven, it will not light the main burner. The pilot light glows red but the main burner will not light!

A:

Managemylife.com is a great place to find the answers to just about anything, especially on appliances. I would suggest that you provide a little more information such as the make and complete model number of your product so your expert will be able to provide you the best possible answer. Just click on reply below where you can provide the additional information. Have a great day!

Read More
Alina F. -
May 11, 2012
A:

Model# FGB24L2ABA

Read More
al -
May 11, 2012
A:

Thank you for your question and I understand your concern.

Based on your symptom and details; the bake glow bar igniter is weak and will need to be replaced. If the glow bar is weak it will not pull enough current/amperage to cause the gas safety valve to open. Replace the bake igniter and your oven should operate normally.

You can look up and order the bake igniter from Sears PartsDirect Sear Parts Direct.

I hope this is helpful. If I may be of further assistance as more details become available, please reply to this post.

Read More
Joey S -
Sears Technician
May 12, 2012
See more answers
Q:

Why won't our Frigidaire Wall oven heat up?

A:

I do not have enough details indicating if the glow bar igniter is glowing red or not. Is the gas turned back ON? Open the broiler drawer and program and start a bake cycle. With the broiler drawer opened you should see the oven igniter glow bright red. If you do not see the igniter glowing red then it may have a failed oven igniter or control board. The oven safety valve is not going to open and let gas out unless the oven igniter glows and pulls enough current to open the gas valve.

I added a couple of images below with the theory of operation and the LP conversion instructions.

Resubmit your question with the model number and additional details if needed for further assistance.

Read More
Joey S -
Sears Technician
April 20, 2009
A:

I have the same problem...the ignitor is glowing red but no gas is flowing thru the burner. Some valve or regulator is not opening??? is there an oven burner needed to be open? -another question for the expert: if the oven is equipped with LP gas regulator, then will burner still burning even when NG gas is connected to it or maybe it works but not safe or not burning effieciently perhaps... thank you

Read More
quang -
July 11, 2011
A:

Quang: If the ignitor is glowing red then the gas valve is not opening because the glow bar ignitor is too weak to pull enough current/amperage to cause the oven safety valve to open. Replace the glow bar igniter and it will likely heat again.

Read More
Joey S -
Sears Technician
July 11, 2011
A:

Is there a way to tes the current on this ignitor or can we based on the level of redness of this bar? I can tell that it is very red and hot but maybe it is not pulling enough amperage? Is there a way to check if the safety valve is working or not? what is the part # for this glow part ignitor? -this is a separate question for the expert: oven is equipped with LP gas regulator, then will burner still burning even when NG gas is connected to it or maybe it works but not safe or not burning effieciently perhaps... thank you quang

Read More
quang -
July 11, 2011
A:

Quang: The current draw is checked with a clamp on amp meter as shown in the images in the link you asked your question in. It will also show you how. You would clamp your amp meter around just one of the wires connected to the igniter. It should pull a minimum of 2.9 amps in order to open the oven safety gas valve. If the igniter is pulling enough current and the gas valve never opens then you can assume the oven safety valve is faulty. If Natural gas is connected then the pressure regulator should also be converted to Natural gas as well, the burner would still ignite but it would not be burning correctly nor would it be safe.

Read More
Joey S -
Sears Technician
July 12, 2011
See more answers

Top Parts