Model #FFU20FC4AW2 FRIGIDAIRE Upright Freezer

  • Door
    3 Results
  • Cabinet
    3 Results
  • System
    3 Results
Find part by diagram >

Error Codes

Error Code:

Condition:

Check/Repair:

Question and Answers

Q:

Kenmore freezer runs almost continually.

A:

I completely understand your concern over your freezer running continuously. While you are waiting for your expert answer, I did some research on the unit. At this time, I was unable to locate information that would be helpful in regards to your question. Some of these questions that are asked will need specific research and will be answered by an expert with-in two business days but usually sooner.

Read More
Julio -
May 20, 2013
A:

I know that it can be very frustrating to have issues with your freezer. If the compressor is running but the unit is not freezing, then make sure the evaporator fan is working and that there's no ice build up in the freezer. A defrost system (heater, thermostat, main control) or a fan failure would cause the unit to stop cooling efficiently. If there is no ice build up and the fan is working then feel how hot the condenser coils are hanging on the back of the unit. The condenser coils should be hot. If the compressor is running but the condenser coils are not hot, then that would indicate a sealed system problem. A defrost or fan problem can be repaired as a do-it-yourself project but a sealed system problem would be expensive and require a technician to fix. You can schedule service at this website Sears Home Services . However due to the age of the freezer, I would suggest that you consider buying a new one. Most manufactures stop producing parts for these after ten years, so there are that may no longer be available. If you need further assistance, please reply to this thread. Thank you for using Manage My Life.

Read More
AnneJ -
Sears Technician
May 21, 2013
See more answers
Q:

FROST FREE FREEZER MODEL FFU20FC4AW2 HAS ICE FORMING ON INSIDE TOP FRONT.

A:

I understand that your frost free freezer has ice forming inside on the top. While you are waiting for an expert to respond, I have attached some helpful links below that may provide information to assist you with your question. Have a great day!

Read More
Alina -
August 31, 2012
A:

Hi,

Thank you for your question. It is concerning when the freezer is not functioning correctly.

With frost forming on the top of the inside, I would think about an air leak between the door and the cabinet. The gasket could have something on it to prevent the gasket from sealing completely. Clean the gasket and the cabinet with a warm soapy water solution and dry off.
The seam where the line and the frame join could be also leaking air into the cabinet. This could be sealed with silicone RTV.

I hope this is helpful. If I may be of further assistance please include more details in a reply below this entry.

Read More
Bill__W -
Sears Technician
August 31, 2012
See more answers
Q:

Instructions for changing out a freezer temperature controller.

A:

When replacing a major part on a refrigerator I know how handy detailed instructions can come in handy. I did some research for you at Managemylife.com and found an expert answer to a similar question that may help until your expert can respond to your specific question. The link is attached below. If you do decide to schedule service and have a qualified technician help you, I have also attached a link to Searshomeservices.com. I hope these links provided assistance for you.

Read More
Joseph P. -
December 14, 2011
A:

To replace the temperature control on your freezer disconnect the power to the freezer. Remove all shelves and the evaporator cover at the rear of the compartment.

Remove the control knob and the 2 screws mounting the control to the evaporator cover. Disconnect the wires from the original control and install them on the new one.

The control has a sensing bulb that is attached to the evaporator coil with a plate. Loosen the screws clamping the plate to the evaporator coil and slide the sensing bulb out. Install the sensing bulb of the new control under the plate and tighten the screws.

Mount the new control to the evaporator cover and install the evaporator cover.

Read More
Jimmy K -
Sears Technician
December 17, 2011
See more answers

Top Parts