Model #FEF366CCB FRIGIDAIRE Free Standing, Electric

  • Backguard
    3 Results
  • Body
    3 Results
  • Top/drawer
    3 Results
  • Door
    3 Results
  • Wiring Schematic
    3 Results
  • Wiring Diagram
    3 Results
Find part by diagram >

Question and Answers

Q:

Control unit turns on and off unexpectedly FEF366CCB Frigidaire Electric range

A:

Thank you for choosing SearsPartsDirect.com and being a valued member.  I can certainly understand how frustrating it can be when your range is not working properly.

It sounds to me like the control board maybe faulty and slowly going out. If it shuts off your oven then there is something wrong with the board or wiring.

You will need to test with a multi meter.
If you have 240 volts when measuring across L1 and L2 IN but have 0 volts across L2 out and BK when set to Bake and O volts across L2 OUT and BRL when set to broil that would indicate a failed electronic oven control.

You can also visit searpartsdirect.com for parts, diagrams, and repair information.

If you do not feel confident repairing this problem yourself, then you can have it repaired at your home by a Sears technician. Here is a link for the website: Sears Home Services .

Thank you for your question. Have a great day. 

Read More
Natasha12 -
Sears Technician
November 21, 2014
Q:

My oven and display does not work but the stove top is working fine. FEF366CCB Frigidaire Electric range

A:

Searspartsdirect.com is always a great resource to find the answers to your parts questions. Your Sears partsdirect expert will research your question and respond within two business days but usually sooner. Thank you for using Searspartsdirect.com!

Read More
Joseph P. -
March 12, 2013
A:

From what I've read on the web, I may need to replace my control board. What part is that and what is the cost?

Read More
Kim -
March 12, 2013
A:

You are correct. That failure is normally caused by a defective control board. That component is part number 316207511. You will normally need to replace the overlay (part 316220805) when replacing that control board.

 

You can order those parts from this page: Frigidaire Electric Range Model FEF366CCB Repair Parts. 

 

Unplug the range before accessing internal components and replacing that control board. Remove the upper back panel behind the console to reach the control board. Note the wiring connections on the back of the control board before removing them (take a digital picture to document the wire locations if necessary). Remove the wires and then replace the control board. Properly connect the wires and reassemble the range.

 

I hope that this information helps. If you need further assistance, reply with additional details.

 

If you get to the point where you need to have a service technician examine and repair the range, you can schedule service through this link: Sears Home Services Range Repair. 

Read More
Lyle W -
Sears Technician
March 13, 2013
See more answers
Q:

One burner not working

A:

Oven's are appliances we count on daily so when it starts to have issues it can be really frustrating. While you are waiting on an expert to answer your question, I suggest you set service with a Sears technician. I have attached the link below. Hope this helps!

Read More
Dezeray -
January 22, 2013
A:

You can unplug the range and access the back of the burner switch for that element in the console. Remove the back panel of the console to access the back of the burner switch. The connection spades on the burner switch should have markings that match the ones in the wiring diagram that I posted below. I marked the wires on that wiring diagram with the wire colors that you should see on the right rear burner. The L1 spade should have a black wire or wires. The L2 spade should have a red wire (or wires). The H1 and the H2 spades should have blue wires (or the color provided for the particular burner that you are testing). Using a volt/ohm meter, you can check for continuity through the element circuit through the blue wires (or the color of wires for the particular element that you are testing). You should measure between 15 and 80 ohms through that circuit. If the circuit is "open" electrically (measures OL -- open load or infinite resistance) then the element is probably bad. There is a slight chance that a wiring failure could cause that "open" circuit condition but that failure is less likely than a failed element.

If that circuit is okay, you can check for continuity between L1 and H1 when the burner switch it turned on (with the range still unplugged ). You can also check the L2 to H2 contact on that switch in the same manner. You should measure continuity through those contacts when the burner is in the "on" position. The resistance will probably be near zero ohms. If you measure OL (open load) during the test of either of those contacts then the burner switch will need to be replaced.

These tips should help you determine the cause of your element heating failure in the range. If you need more help, reply with additional details.

You can order parts from this page: Frigidaire Range Model FEF366CCB Parts . Be sure that you unplug the range before accessing internal components and replacing parts.

If you get to the point where you need to have a service technician diagnose and repair this failure, you can schedule service through this link: Sears Home Services .

Read More
Lyle W -
Sears Technician
January 22, 2013
A:

Here is the wiring diagram image.

Read More
Lyle W -
Sears Technician
January 22, 2013
See more answers

Top Parts