Model #FEF365BWF FRIGIDAIRE Free Standing, Electric

  • Backguard
    3 Results
  • Body
    3 Results
  • Top/drawer
    3 Results
  • Door
    3 Results
  • Wiring Schematic
    3 Results
  • Wiring Schematic
    3 Results
  • Wiring Diagram
    3 Results
  • Wiring Diagram
    3 Results
Find part by diagram >

Question and Answers

Q:

Why isn't my oven baking evenly?

A:

If the oven temperature is still not baking correctly after replacing the element, you might try calibration while waiting for the expert response. I see the owner's manual has instructions on page 21. I attached the manual below as well as a helpful article for calibration. I hope one of these helps.

Read More
Barbara H. -
April 29, 2012
A:

Thank you for submitting your question and I will be happy to assist you. Your range could have a faulty temperature sensor or electronic oven control board. You'll need a ohms/volt meter to test the temperature sensor. If the oven sensor test good then you'll need to replace the electronic control. Here's a video on how to test the temperature sensor and here's a video on how to replace it. You can order parts from our Sears Parts Direct team. If you do not feel confident repairing this problem yourself, then I recommend scheduling for service online with our Sears Home Services team. Click on the red Start now button. I hope this helps. Thank you for choosing Manage My Life.

Read More
Tykara -
Sears Technician
April 30, 2012
See more answers
Q:

Oven does not work on FEF365BWF

A:

The oven not heating properly can keep you from cooking up a nice meal and I will be happy to help. I did some research and came across a link that may provide you with some good information about what may be causing the problem on your oven. I hope this helps while you wait for your expert response.

Read More
Joseph P. -
January 17, 2012
A:

I see those brown spots in the picture. The image below shows the wiring diagram for your range with the affected circuits traced in colors. You could have had a short in the bake element or the light circuit that damaged the control board. I recommend that you unplug the range and check the wiring on the back of that control board. Here is a link for a brief repair video that shows how to access that control board: Range Clock Control Board Replacement . You may find some wires on that control board where the insulation is burnt or melted. If you do, then I recommend that you check that circuit more closely. If the yellow or orange wire for the bake element are burnt, I recommend that you check the resistance of that bake element as shown in this brief video: Bake and Broil Element Testing . You can test the bake element with it still installed. Just remove one wire and measure the resistance (with the range still unplugged ). Also, check the resistance from the element to the bare metal cabinet on the range (touch one probe to the element spade and the other lead of your meter to the bare metal on the back of the range). You should measure between 10 and 40 ohms through the element. You should measure infinite resistance (Ol -- open load) between the element and the metal cabinet. If that bake element is okay, you may also want to check the broil element in the same manner.

Since that light works, that is not likely a cause of your current problem. That burn mark on the light socket could have occurred when a light burnt out. You can check that light socket for a short to the cabinet in the same manner as described above if you suspect that you have that type of problem. Make sure that you have the range unplugged when checking that issue.

There is a possibility that you had an internal short in that clock control board and you may be able to fix this problem yourself by just replacing that clock control board. You can order that part from the Sears PartsDirect website. You may also need to order the overlay unless you can reuse the original one as shown in that video.

These tips may help you fix this problem on your own. If you need more help, reply with additional details.

If you get to a point where you need to have a service technician examine and repair the range, you can schedule service through this link: Sears Home Services .

Read More
Lyle W -
Sears Technician
January 18, 2012
See more answers
Q:

f1code frigidaire model fef365bwf

A:

Having an error code on your range since this can keep your range from working properly and I will be happy to help. While you are waiting for an expert answer, I did manage to find a link that will provide you with some tips about what may be causing your error code. I hope my link is useful.

Read More
Joseph P. -
April 04, 2011
A:

Thank you for your question and I understand your concern.

The "F1" fault code generally implies a shorted key pad/stuck button meaning it will need a new oven control.

It can also mean the control board has sensed a potential runaway oven condition. The control board may have a shorted relay or the RTD (temperature sensor) may have gone bad.

The oven temperature sensor (RTD) should be disconnected and measured for resistance using an OHM meter. The sensor leads can be accessed from the rear of the range. Disconnect the range from the power source and then remove the rear panel. The sensor is usually located in the upper left hand corner when looking into the oven cavity and it will be in the upper right hand corner when looking from the rear of the range. The oven temperature sensor (RTD) should measure approximately 1100 ohms at room temperature. If it measures approximately 1100 ohms then the electronic oven control (EOC) will need to be replaced.

I added a YouTube video showing how to test the sensor.

Parts can be looked up and ordered from Sears PartsDirect

If you do not feel confident repairing this problem yourself, then you can have it repaired at your home by a Sears technician. Here is a link for the website: Sears Home Services .

Read More
Joey S -
Sears Technician
April 06, 2011
See more answers

Top Parts