Model #FEC30S6ABF FRIGIDAIRE Counter Unit Electric

  • Controls
    3 Results
  • Maintop
    3 Results
  • Wiring Diagram
    3 Results
  • Wiring Diagram
    3 Results
Find part by diagram >

Question and Answers

Q:

electrolux frigidaire electric cooktop FEC30S6ABF Frigidaire Electric cooktop

A:

I know that it can be very frustrating to have issues with your cooktop. That type of failure is normally caused by a failed burner switch. You can order that switch from the Sears PartsDirect website. You may be able to replace that burner switch yourself by shutting off the circuit breaker for the cook top and pulling it out of the counter. Here is a link for the installation guide that will help you remove that cook top from the counter: Installation Instructions . Once you remove the cook top, you can remove the knob from that burner switch and then pull the service panel off of the bottom of the cook top. Once you get that panel off, you can replace that burner switch. Be sure that you note the location of wires on the original switch before replacing it. This is a basic repair that you may be able to complete yourself if you can properly disconnect electrical power to the cook top and then access that switch as described above. If you don't feel comfortable doing this yourself, please click on this link to schedule service: Sears Home Services. Click on "Get Started" and follow the directions, click on the red "NEXT" button to continue. I hope this helps. Please feel free to let me know if you need further assistance. We are always here to help. Thank you for using Manage My Life.com.

Read More
AnneJ -
Sears Technician
September 29, 2013
A:

what is the part number ? It is the large 9 inch burner and is the first dial on my cooktop so it may be different from your manual. Again I emphasize, it is the LARGE burner located in the front right side of cooktop. Please give me part number as this is confusing to the Sears order tech on the phone !

Read More
tina -
September 30, 2013
A:

This is part number 318369610. You an order it from the link below. Please let me know if there is anything else you need. Thank you for using Manage My Life.

Read More
AnneJ -
Sears Technician
October 01, 2013
See more answers
Q:

electrolux frigidaire electric cooktop, burner not working FEC30S6ABF

A:

I know that it can be very frustrating to have issues with your cooktop. That type of failure is normally caused by a failed burner switch. You can order that switch from the Sears PartsDirect website. You may be able to replace that burner switch yourself by shutting off the circuit breaker for the cook top and pulling it out of the counter. Here is a link for the installation guide that will help you remove that cook top from the counter: Installation Instructions . Once you remove the cook top, you can remove the knob from that burner switch and then pull the service panel off of the bottom of the cook top. Once you get that panel off, you can replace that burner switch. Be sure that you note the location of wires on the original switch before replacing it. This is a basic repair that you may be able to complete yourself if you can properly disconnect electrical power to the cook top and then access that switch as described above. If you don't feel comfortable doing this yourself, please click on this link to schedule service: Sears Home Services. Click on "Get Started" and follow the directions, click on the red "NEXT" button to continue. I hope this helps. Please feel free to let me know if you need further assistance. We are always here to help. Thank you for using Manage My Life.com.

Read More
AnneJ -
Sears Technician
September 29, 2013
Q:

burner won't turn off

A:

Some repairs can be done by a homeowner and if it is an easy fix I would also prefer to do myself. The expert will be able to review your model and respond with information. If you do want a technician to handle the repair, you can schedule at the Sears Home Services and there is a contact number if you need to get information about the charge to visit. I attached that link below.

Read More
Barbara H. -
September 18, 2011
A:

That type of failure is normally caused by a failed burner switch (part 318293825 for the large burner). You can order that switch from the Sears PartsDirect website. You may be able to replace that burner switch yourself by shutting off the circuit breaker for the cook top and pulling it out of the counter. Here is a link for the installation guide that will help you remove that cook top from the counter: Installation Instructions . Once you remove the cook top, you can remove the knob from that burner switch and then pull the service panel off of the bottom of the cook top. That service panel is shown as KEY 23 in that parts image below. Once you get that panel off, you can replace that burner switch. Be sure that you note the location of wires on the original switch before replacing it.

This is a basic repair that you may be able to complete yourself if you can properly disconnect electrical power to the cook top and then access that switch as described above. If you are not completely confident that you can perform that repair, I recommend that you schedule a service technician to fix the cook top. Here is a link for the Sears Service website Sears Home Services . . The repair by a technician will probably cost around $180.

Read More
Lyle W -
Sears Technician
September 21, 2011
A:

Lyle, I have the same stove top that had the same issue. Someone else had pulled the switch out and taped off the hot wires to keep using the stove. I pulled the wiring diagram and connected it the way I read the diagram, but have burnt up 2 switches (3rd is on order now). When I turn on the big burner by itself, it works fine, but if I turn on any other burners with the big burner on, it shorts out the switch. There is a blue wire that has a piggy back blade on it. I was connecting it to black line in. Can you help me sort this out?

Read More
Greg -
January 15, 2013
A:

Hello Greg. I posted the wiring diagram for that cooktop (Model FEC30S6ABF) in the images below. You indicated that you need help wiring the big burner. There appears to be a large burner on the left rear and a large burner on the right front of that model. Which burner switch are you working on? That wiring diagram covers several models with different surface element configurations. I will try to help you sort this problem out but I just need to know the location of the burner.

Read More
Lyle W -
Sears Technician
January 16, 2013
A:

It is the right front big burner. The switch I get when ordering is a little different than the original. It has a slightly bigger housing and the pins are in different locations, so I have to go by the marks next to each pin. The diagrams you sent are the same that I have. I wired it according to the third diagram on the first page. Note that the hot surface light has white and yellow wires in lieu of the blue 5 wire and can't be changed, because the connectors are smaller on the light than on the switch.

Read More
Greg -
January 16, 2013
A:

Sorry Lyle, I was wrong on the wire colors going to the Hot Surface light. It is a yellow and red. The red comes from the L2, so I think it is what is marked as BL-5 on the diagram. I had the blue wire attached to the black (L1) wire. The new switch they sent me is part number 318293824. Thanks for your help.

Read More
Greg -
January 19, 2013
A:

Hello Greg. Thanks for sending the photograph and the additional information. I referred to the legends on the wiring diagram and I marked the portion of the wiring diagram that appears to apply to the right front burner. I don't see any gray wires on your right front burner switch even though the wiring diagram seems to indicate that there should be one. The wiring diagram indicates the L2 wire is red. I am not able to see all of the labels for the spade contacts on that burner switch. I recommend that you examine the wiring diagram that I provided below and see if it applies to that burner.

Read More
Lyle W -
Sears Technician
January 21, 2013
A:

I piggybacked the blue wire off of L1 with the black wire. I now believe that it is supposed to piggyback off of H1 with the brown wire.

Read More
Greg -
January 21, 2013
See more answers

Top Parts