Model #FDB710LCS0 FRIGIDAIRE Dishwasher

  • Control Panel
    3 Results
  • Door
    3 Results
  • Tub
    3 Results
  • Motor & Pump
    3 Results
  • Frame
    3 Results
  • Racks
    3 Results
Find part by diagram >

Troubleshooting

Question and Answers

Q:

Top spinner not getting water FDB710LCS0 Frigidaire Dishwasher

A:

Thanks for your question- we see that no one from the community responded.  If you still require assistance on this topic, please resubmit your question with any updated information and we will have one of our experts take a look.  Also, we have updated our site to include information regarding common repairs and diagnosis, which can be found here: www.searspartsdirect.com/repair-help.html.  If you are looking for your owner’s manual, it can be found here: http://www.searspartsdirect.com/partsdirect/user-manuals.  Thanks for visiting SearsPartsDirect.com.

Read More
Natasha12 -
Sears Technician
January 14, 2014
Q:

Overheating FDB710LCS0 Frigidaire Dishwasher

A:

I know that it can be very inconvenient for you not to have your dishwasher working properly. While you are waiting for an expert to respond, I have attached a helpful link below that may provide information to assist you with your question.

Read More
Yadira B -
January 31, 2013
A:

I do not see a link ("I have attached a helpful link below that may provide information to assist you with your question.")

Read More
Walley -
January 31, 2013
A:

Thank you for your question and I understand your concern.

The timer is only going to advance once the temperature boost thermostat closes and completes the voltage path to the timer.

The Wash Temperature Boost thermostat should close once it detects 117�F plus or minus 5 degrees. Note; this is with the outer door in place.

The Rinse Temperature Boost thermostat should close once it detects 122�F.

The Hi-Limit Thermostat will open at 200�F and break the heater circuit and shut off the heater in case the timer was to stall or if one the Boost thermostats were to fail and stick closed.

If the heater is working and the wash or rinse boost thermostat is not making a good contact with the tub or inner door liner, the thermostat will not close. If your were to heat the rinse or boost thermostat up with the soldering iron based on the cycle the timer is in and it closes, the timer should begin to advance. It it does, the thermostat is not likely sensing the temperature of the tub because the thermostat may not be sitting up against the tub/inner door panel tight enough so the heat can transfer to the thermostat.

I hope this is helpful. If I may be of further assistance as more details become available, please reply to this post.

Read More
Joey S -
Sears Technician
February 01, 2013
A:

I am almost there.... Thank you so much for your assistance. Is it my understanding that the "Hi-Temp Rinse" button then serves as an electrical by-pass to the "Rinse Temperature Boost" thermostat? The switch and the thermo disc are in parallel...so the use of the switch indicates that the circuits are fine...and the thermo disc ("Rinse Temperature Boost thermostat ") is somehow failing? For my testing of the "Rinse Temperature Boost thermostat " I did remove and replace; it seemed to have good contact with the tub...so at this time the assumption is a failing thermostat. So now I only need to order a new thermostat.

Read More
Walley -
February 01, 2013
A:

Wally: That is correct. Based on your symptom the "Rinse: boost thermostat is not closing. If you by pass the rinse thermostat by disconnecting the two wires from the "Rinse" boost t-stat and then connecting the two wires together, the timer should advance in the rinse cycle. This would also confirm the high temp rinse switch is working too.

Read More
Joey S -
Sears Technician
February 01, 2013
A:

Thank you.

Read More
Walley -
February 01, 2013
See more answers
Q:

frigidaire dishwasher fdb710lcs0 i need the rubber coupler that connects the delivery tube to the pump.. about 2 inch long by 7/8 not shown on specs.

A:

When I am trying to find a part for my appliance I have found it helpful to visit the PartsDirect website. If your unable to locate the desired parts you can chat or speak with an associate on this website, they will further your search. I have provided the link below. I hope this helps!

Read More
Jacqueline S -
September 06, 2010
A:

The drain hose has the 90 degree elbow connected to the pump; 154525301, $26.25. The sump to pump hose connects to the other end of the pump; 154234401, $15.02. Delivery tube; 154406601, $34.10 www.searspartsdirect.com If you need another hose please provide a better description or digital photo.

Please see the image provided below for more information.

If you do not feel confident repairing this problem yourself, then you can have it repaired at your home by a Sears technician. Here is a link for the website: Sears Home Services .

SAFETY NOTICE: Be sure to disconnect power to the appliance before performing any repairs. If you are not comfortable with doing any voltage checks that might be recommended, please contact your local service provider for repairs. Be aware that there could be sharp edges inside the appliance that could cause cuts or other injuries to yourself or others.

Read More
biker dave -
Sears Technician
September 08, 2010
See more answers

Top Parts