Model #F220 JENN-AIR Free Standing, Electric

  • Unique Range/bottom Oven Parts
    3 Results
  • Unique Cabinet Base Parts
    3 Results
  • Cabinet
    3 Results
  • Door & Latch Parts (mw Upper Oven)
    3 Results
  • Microwave Components-upper & Chassis
    3 Results
  • Magnetron & Air Flow Parts
    3 Results
  • Wiring Harness (microwave)
    3 Results
  • Control Panel (microwave)
    3 Results
  • Electronic Air Cleaner Parts
    3 Results
Find part by diagram >

Question and Answers

Q:

Hoover SteamVac Dual V Carpet Cleaner F7412-900 will not spray water/cleaner on WASH, but RINSE works fine.

A:

Thank you for your question as to why the solution will not dispense but the rinse water will.

It sounds like the valve cap is clogged and you will need to clean it before it will dispense solution.

I have given you the instructions in the image below.

If it does not solve the problem we can continue to troubleshoot.

Thank you.

Read More
Sam A -
Sears Technician
November 19, 2012
A:

Thank you for the update Sherry. It is highly likely that the dual switch has failed if before you had to switch it back and forth to get it to work. I would suggest replacing the dual switch in the handle. If you decide to repair it yourself you will need to remove the tool rack on the back of the handle and then remove the screws on the back side of the handle to gain access to the duel switch inside the handle. I will give you the part number for the switch below in the link. Sam A.

Read More
Sam A -
Sears Technician
November 20, 2012
A:

Thank you for the update on the carpet cleaner. This unit has a micro switch on the right wheel so when you back up with the cleaner it turns the solution shampoo off and just let’s rinse water through to the carpet. When go forward again and you have the trigger pulled it with mix the clear water with the soap solution. The pump will work for the hose cleaning but it sounds like the solution side is not working. If you can get soap and water out the hose cleaning system that will tell you that the pump is working. So it could be the micro-switch or the solenoid valve that is causing the problem. There also is a separate pump solenoid that opens during the solution dispensing and a reverse pressure valve that also is in the water system to change from mix the water with the solution. I will give you three flow charts that may help you. Is the carpet cleaner at one of the Sears repair locations for at an authorized Hoover repair location? Sam A.

Read More
Sam A -
Sears Technician
November 21, 2012
A:

Thank you for the update on the Auto rinse. I see that it is optional on some models. Only some of the information would help with the diagnosis of the problem you are having. I am thinking that maybe the hydraulic valve is the problem. Was the dealer you took it to an authorized Hoover repair location? If they were not then I would suggest that you find one in your area if there is one. I can also give you a contact at Hoover that may help you solve the problem or at least direct you to a Hoover repair station. 1-800-944-9200. Sam A.

Read More
Sam A -
Sears Technician
November 24, 2012
A:

Thank you posting the details. If you do not get and water pressure in any mode, I suspect the pump is the problem. To be sure, I recommend checking the voltage to the pump. First, gain access to the pump. Then connect your meter leads to the pump wires. Once they are connected plug the unit in and check the voltage. If you have voltage to the pump and it does not run the pump is defective. I hope this is helpful. Please let me know what you find. Thank you for using Manage my life. Mark T.

Read More
Mark T -
Sears Technician
January 08, 2013
See more answers
Q:

What are temperature equivalents for the most often used oven settings?

A:

The Fahrenheit and Celsius equivalents for the most often used oven settings are: 325*F (170*C) 350*F (180*C) 375*F (190*C) 400*F (200*C) 425*F (220*C) 450*F )230*C) 475*F (240*C)

Read More
Nicole A. -
Sears Technician
January 17, 2010
Q:

What does the high temperature limit switch on a boiler do?

A:

This switch performs the same function as the high-temperature limit on a furnace: it shuts off the boiler if the temperature gets too high. This switch is located either in the boiler or in the supply piping just above the boiler. It is typically set at 200F to 220F. A common setting is 210F. On most systems you can look at the limit switch and see its setting.



Read More
expert -
Sears Technician
April 26, 2007