Model #F-1 INSTAPURE Water filter

  • Replacement Parts
    3 Results
Find part by diagram >

Question and Answers

Q:

TV wont turn on LN46C530F1FXZA Samsung Lcd tv

A:

I'm having the same problem, did you figure it out? I was having trouble turning on my TV, so I just left it on. My daughter came over today and turned it off, ugh, now it won't come back on.

Read More
HALEY -
December 23, 2015
Q:

My Duet dryer Has an Error Code F01

A:

A Washer is definitely something we depend on and when it begins to malfunction it can be a huge inconvenience. While you are waiting for an expert to respond, I have attached some helpful links below that may provide information to assist you with your question.

Read More
Priscilla V -
January 03, 2012
A:

I see Pvalde2 provided you with good information however, it does not pertain to a dryer. The F-01 error code indicates a primary control board failure on this model of dryer. If the error cleared after unplugging it for 20-30, then the control board could have received a power surge or glitch through the electrical lines. Completely disconnecting the electrical power and then reconnecting it will sometimes reset the board and it will operate properly. If your dryer continues to operate properly, then resetting the control board may have fixed your problem.

If the dryer motor continues to stop working, then you may have a bad control board. A wiring problem or drive motor failure could also prevent the dryer from continuing to run properly. A technician is normally needed to diagnose and repair this type of problem. If the F-01 returns and will not clear, then you will need to replace the control board in the dryer.

If you do not feel comfortable repairing the unit yourself, service can be scheduled at the following link: Sears Home Services . For further assistance, please respond to this thread with more detail. I hope this helps.

Read More
Korinna S -
Sears Technician
January 05, 2012
A:

Is it easy to replace the control board?

Read More
lisa -
September 17, 2012
A:

Please be sure to unplug the dryer prior to attempting any service or repair. I have included the instructions from the service manual that explain the process. Look it over and if you do not feel comfortable performing the task, service can be scheduled at the Sears Home Services link I provided above. For further assistance, please respond to this thread. I hope this helps.

Read More
Korinna S -
Sears Technician
September 18, 2012
A:

What would be part number for control board, where can I get one, and finially how much?

Read More
Sam -
November 14, 2012
A:

Hello Sam. WED9400SU is a partial model number that brings up 3 models. Two of the model have the same part number for the control board, while the other is different. Once you have the complete model number of your specific model, you can search for the part and purchase it from Sears PartsDirect. The diagram you want to be looking at is the "Dryer Cabinet" diagram. The control board you need is number 41 on the diagram. I really hope this information helps you today. For further assistance, please respond to this thread. I will be delighted to assist you. Thank you for using ManageMyLife.com

Read More
Korinna S -
Sears Technician
November 16, 2012
A:

I have a whirlpool duet sport gas model number WGD8300SW1, It started with F-1 error code, I checked control board and it had burn mark, so I changed it. the F-1 code is gone but I have NO heat. I take any help!

Read More
Sam -
November 24, 2012
A:

Hey there Korinna, the images you provided above are really small, can you please repost larger images?

Read More
clipper -
April 12, 2015
A:

i have a whirlpool duet dryer model number 4WED9200SQ1 i get an error message F1 what can i do myself to fix this please and thank u i put some clothes in it shut the door and it did start but then stopped and i heard a click sound then got the error i went to the fuse box and clicked it on and off and nothing it still wont work is there anyway i can do it myself at home appreciate any help u can give me thank u

Read More
denise -
May 25, 2015
A:

Hello, I have a Whirlpool dryer model Wgd8300sw1 that is giving me error code F-01. It does not clear when the unit is power cycled. Does the main control board need to be replaced, part number W10111606? Or what is the solution? Thank you.

Read More
Steven -
November 16, 2015
See more answers
Q:

What can cause my TV to have a ghost down the screen?

A:

I am not sure what your exact symptom is. If you are hooked up to analog cable (straight from the wall no box) it is possible that the cabling is leaking or combining signals to give a "ghost" image of itself on the side. This problem is a type of interference and only exists with analog signals. Go through your connections and try to eliminate the splitters first and see if you can get a clear picture by hooking up the TV as direct as possible to the source. Calling the cable company might be necessary. Also keep in mind that the TV menu cannot be affected by this and would not be ghosting as well. If you are hooked up with an antenna (broadcast is now digital) or a type of digital system (like satellite or digital cable) this would not be your problem.

Another possibility is that you are describing a defect in the TV itself. I cannot remember seeing a Vizio do this but it is possible that a defective board is recreating a ghost like effect. The one thing to note is that the menu would more than likely be affected as well. You would be able to see a ghost of the menu or volume bar where the video is being shifted to as well.

The other scenario that came to mind is that you are trying to describe a defect in the panel to me. I have seen a lot of LCD panels that have a shadowy, non uniform crescent moon or line that I describe as looking like a water mark. Some people have used the term "ghost" as well for this symptom. This is a problem in the panel and I believe that it has to do with the layers of screens used that are becoming loose.

Read More
David A. - Personal Solutions Manager -
Sears Technician
October 07, 2009
A:

My screen is all white with alittle color, and I do have sound. Now my HDMI ports in the back went out first, then about a week later my screen is doing the white thing. So I installed a new "main board" and that fixed my HDMI ports but im still getting the white screen. Do you have an idea what I should do next? Im enclosing photos.

Read More
Kelly -
October 31, 2011
A:

It would seem that you have a T-con issue. Not all T-con boards are replaceable. I would need your model number to better assist you. Also, You can ask this as a new question.

Read More
Dusty J -
Sears Technician
November 07, 2011
A:

I have a Vizio model# VOJ320F1a If it is the T-Con board, where would it be located at in the back? Thanks so much

Read More
Kelly -
November 07, 2011
A:

The t-con board is at the top of the LCD panel. The long flat connector that goes from the main board to the LCD panel actually goes to the T-con board. The t-con board was not supplied by the manufacture are a replaceable part.

Read More
Dusty J -
Sears Technician
November 08, 2011
A:

I also have a Vizio VOJ32OF1A, and for the last few months the screen has started to flicker dark, then bright, getting darker and darker over time. Is it the screen itself giving out, or a light I can replace?

Read More
Mike -
November 14, 2015
See more answers