Model #ED25TQXFN00 WHIRLPOOL Side-by-Side Refrigerator

  • Cabinet
    3 Results
  • Refrigerator Liner
    3 Results
  • Refrigerator Shelf
    3 Results
  • Freezer Liner
    3 Results
  • Motor And Ice Container
    3 Results
  • Refrigerator Door
    3 Results
  • Freezer Door
    3 Results
  • Dispenser Front
    3 Results
  • Unit
    3 Results
  • Air Flow
    3 Results
  • Control
    3 Results
  • Icemaker
    3 Results
Find part by diagram >

Error Codes

Error Code:

Condition:

Check/Repair:

Question and Answers

Q:

ice door won't stay closed model ED25TQXFN00 side by side frige. need to know how to get to the spring so i can replace it.

A:

I understand how inconvenient it can be to have a fridge door not closing properly. While you are waiting for an expert answer, I did manage to find a useful link about how to replace a door, now you can also click in the link that describes the parts direct website and take a look at all of the parts on your specific model. I hope this link is useful.

Read More
Joseph P. -
August 28, 2010
A:

To replace the flapper door on your refrigerator disconnect the power to the refrigerator.

  • On the bottom edge of the trim around the dispenser are two notches for a flatblade screwdriver blade to fit and pry it off. Pry it off and lift the trim up to clear the tabs at the top. Let the outer trim hang by the wires going to it.

  • Remove the 2 screws holding the bracket across the top of the dispenser area and carefully swing the bracket back and out of your way.

  • Now you can see the cradle and the flapper door. The flapper door is held to the cradle by a pin and there is a spring on it. Note the position of the spring so you can reinstall it when you put the new spring in.

  • There is also a small ribbon connector that connects the wiring from the flapper door to the harness inside the dispenser area. Disconnect it and you can replace the flapper door.

If you will log on to www.searspartsdirect.com and select parts and enter your model number you can see a parts diagram of the dispenser of your refrigerator. Looking at the parts diagram will make following these instructions easier.

Read More
Jimmy K -
Sears Technician
August 30, 2010
See more answers
Q:

ice door won't stay closed model ED25TQXFN00 side by side whirlpool frige. need to know how to replace spring. i can't figure out how to get to the part.

A:

I can understand your concern on your refrigerator, as a suggestion to help you while you are waiting for the experts response I have provided a couple of links to Manage my life were a customer posted a similar question to yours, and a link to sears parts direct were you can see a diagram of your parts. Hope it helps!

Read More
Maira E -
August 28, 2010
A:

  • On the bottom edge of the trim around the dispenser are two notches for a flatblade screwdriver blade to fit and pry it off. Pry it off and lift the trim up to clear the tabs at the top. Let the outer trim hang by the wires going to it.

  • Remove the 2 screws holding the bracket across the top of the dispenser area and carefully swing the bracket back and out of your way.

  • Now you can see the cradle and the flapper door. The flapper door is held to the cradle by a pin and there is a spring on it. Note the position of the spring so you can reinstall it when you put the new spring in.

  • There is also a small ribbon connector that connects the wiring from the flapper door to the harness inside the dispenser area. Disconnect it and you can replace the flapper door.

If you will log on to www.searspartsdirect.com and select parts and enter your model number you can see a parts diagram of the dispenser of your refrigerator. Looking at the parts diagram will make following these instructions easier.

Read More
Jimmy K -
Sears Technician
August 30, 2010
See more answers

Top Parts