Model #ED25TEXHW00 WHIRLPOOL Side-by-Side Refrigerator

  • Cabinet/literature
    3 Results
  • Refrigerator Liner
    3 Results
  • Refrigerator Shelf
    3 Results
  • Freezer Liner
    3 Results
  • Motor And Ice Container
    3 Results
  • Refrigerator Door
    3 Results
  • Freezer Door
    3 Results
  • Dispenser Front
    3 Results
  • Unit
    3 Results
  • Air Flow
    3 Results
  • Control
    3 Results
  • Icemaker/optional
    3 Results
Find part by diagram >

Error Codes

Error Code:

Condition:

Check/Repair:

Question and Answers

Q:

I ordered inlet valve for icemaker & rec'd part # 2206123 (replaces part # 2204358) Need help with hookup

A:

When it comes to replacing parts on the refrigerator can be difficult. I have taken the time to research on the Manage My Life website and have located a link similar to your issue. While you are waiting for a detailed reply from an expert I have provided the link below. Hope this helps!

Read More
Priscilla V -
May 27, 2012
A:

Thank you for your question. Replacing some parts can be a challenge sometimes. There is only one water valve for this refrigerator. I suspect you may be having some difficulty with the water connections on the valve. The replacement valve will have the new type water connections. I'm attaching a picture with instructions for this type of fitting. I hope this will help you. If you would like more assistance, reply to this thread and I will be glad to assist you further.

If you do not feel confident repairing this problem yourself, then you can have it repaired at your home by a Sears technician. Here is a link for the website: Sears Home Services .

Read More
Scott D -
Sears Technician
May 29, 2012
A:

Thanks, Scott for your expert reply. We did figure the connections out. Problem now is that water is going into the ice maker, but not making ice.

Read More
denise -
May 29, 2012
A:

Denise, if there is ice in the mold but it's not being harvested, it will be due to the icemaker itself or the temperature in the freezer is not cold enough (below 12 degrees), to cycle the icemaker. If the temperature is ok, the icemaker # 4317943 will need to be replaced. If the temperature is too warm, usually adjusting the control to a colder setting will correct it. I hope this will help you.

Read More
Scott D -
Sears Technician
May 29, 2012
A:

We have ice! Took your advice and turned the temp down. Thanks a million!!!

Read More
denise -
May 31, 2012
A:

Denise, I'm glad the icemaker is working. Thank you for using Manage My Life.

Read More
Scott D -
Sears Technician
June 01, 2012
See more answers
Q:

My Whirlpool refrigerator/freezer stopped running about a month ago. Since then they both come on and go off for days at a time. Help

A:

Hi, I see your refrigerator and freezer stopped working. You can visit our SearsHomeServices.com website. I attached the link below. Hope this helps!

Read More
Dezeray S -
July 14, 2010
A:

SAFETY NOTICE: Be sure to disconnect power to the appliance before performing any repairs. If you are not comfortable with doing any voltage checks that might be recommended, please contact your local service provider for repairs. Be aware that there could be sharp edges inside the appliance that could cause cuts or other injuries to yourself or others.

Thank you for a very good description of the symptoms. On something like this I suspect the operating thermostat. If the operating thermostat contacts become weak, burnt or pitted they will not open & close completely all the time causing the unit not to cycle on for cooling. Sometimes with just enough movement from the door closing will cause the unit to come on & run when you have a defective operating thermostat. I recommend replacing the thermostat part number 2198202 www.searspartsdirect.com

Be sure to disconnect power before attempting repairs. Please reference the image provided below for access details. First, remove the control knobs #’s 26 & 27, carefully pry out the escutcheon cover #25 to access the 2 screws #3, slide the control forward about 1 inch to release the rear tabs. The thermostat screws are #10 & the thermostat is #9. Replace exactly as removed. Be careful & do not bend the thermostat bulb while installing.

Other possibilities; compressor, fan, defrost timer or wiring harness problems.

If you do not feel confident repairing this problem yourself, then you can have it repaired at your home by a Sears technician. Here is a link for the website: Sears Home Services .

Read More
biker dave -
Sears Technician
July 17, 2010
See more answers

Top Parts