Model #ED22TEXHW00 WHIRLPOOL Side-by-Side Refrigerator

  • Cabinet/literature
    3 Results
  • Refrigerator Liner
    3 Results
  • Refrigerator Shelf
    3 Results
  • Freezer Liner
    3 Results
  • Motor And Ice Container
    3 Results
  • Refrigerator Door
    3 Results
  • Freezer Door
    3 Results
  • Dispenser Front
    3 Results
  • Unit
    3 Results
  • Air Flow
    3 Results
  • Control
    3 Results
  • Ice Maker/optional
    3 Results
Find part by diagram >

Error Codes

Error Code:

Condition:

Check/Repair:

Question and Answers

Q:

The water fill tube for the ice machine on my Whirlpool Refrigerator is not dispensing water.

A:

I know that it can be very frustrating to have issues with your ice maker. The link below will provide some troubleshooting for this issue. It is for a different model, but the manufacturers are the same. I hope this helps. Thank you for using Manage My Life.

Read More
aashe -
November 13, 2012
A:

I know that it can be very frustrating to have issues with your ice maker. The issue could be a failure with either the ice maker itself or the water valve. The images below will instruct you on how to test the ice maker and valve. If the module cycles properly in the test mode, it should fill the mold (tray) with water. If not, you could have a module failure or a wiring problem between the ice maker and the solenoid water valve. You can check the resistance of this circuit by unplugging the refrigerator and measuring the resistance between test points V and N. I hope this helps. If you need further assistance, please reply to this thread. Thank you for using Manage My Life.

Read More
AnneJ -
Sears Technician
November 14, 2012
A:

I'm not the greatest with a multimeter. But I unplugged the frig and, if I'm reading it right (I set the dial to 200), test points L and H give me 70 ohms like they should, but test points L and M give me 70 ohms (instead of 4400), and test points V and N give me 170 ohms (instead of 300). I was assuming that the water valve was bad, since I hadn't changed the filter, and the fill tube must have been leaking in order for it to freeze. But does this mean that I should assume that the whole ice maker assembly is bad? Should I assume that the water valve is also bad (since the fill tube leaked/froze) or is it possible that the water valve still works and just the ice maker assembly is bad? Is there a way to test that? And I wasn't sure from your instructions how to cycle the module in the test mode Thanks for your help! This is a really great, informative site.

Read More
scott -
November 14, 2012
A:

Couple extra things. I looked up the test mode, and testing the water valve. When the icemaker is in test mode with the jumper in place, the auger continues to spin all the way around, but the water does not come out. I checked the water line from the valve to the icemaker, and it is clear. I checked the freezer temperature, and it is 5 degrees. I pulled out the water valve. There are 3 connectors on it. I tested each one with the ohmmeter. Two tested at 360 ohms, and one tested at 170 ohms.

Read More
scott -
November 15, 2012
A:

The easiest way to test the ice maker assembly is to defrost the fill tube, so you know there is no abstruction in the line. Then take an inslulated jumper wire and inster the ends into the V and N points. If the ice maker fills with water, then ice maker assembly is bad and needs to be replaced. If it does not, then replace the water valve. Please let me know if you need anything else. Thank you for using Manage My Life.

Read More
AnneJ -
Sears Technician
November 16, 2012
A:

Thanks for your reply. I posted one last comment a few days ago, but it didn't go up for some reason. Anyhow, yes, I did jump V and N and the water did come out. So, I understand that the water valve is working. When you say that the ice maker assembly needs replaced, do you mean the entire ice maker assembly, or just the motor module. Is there a way to tell which is broke?

Read More
scott -
November 16, 2012
A:

The ice maker is not a part that can be taken apart and put back together easily. Most technician won't even atempt to repair these. It would be easier for you if you order to whole assembly and replace it. This is part number 4317943 and you can order it from the link below. Please let me know if you need anything else. Thank you for using Manage My Life.

Read More
AnneJ -
Sears Technician
November 18, 2012
A:

Link

Read More
AnneJ -
Sears Technician
November 18, 2012
A:

I'm at a bit of a loss here. I took your advice, and replaced the entire ice maker assembly. The auger on the new icemaker spins as it should. But when it completes it's cycle, no water is coming out. I went ahead and jumped V and N on the new ice maker as you suggested, and water comes out just fine. So, new part, same problem. The augers on both the old icemaker and new icemaker spin, heating coil works on both. When I jump V and N on both, water comes out just fine. If I manually pour water into both, they both make ice, spin and release the ice. But neither one will deliver water on it's own during a cycle. help, please!

Read More
scott -
November 30, 2012
A:

It sounds like the ice maker and the water valve are fine. That means that the wiring harness between them is not. These two parts will direct communicate with each other, so if the harness is bad, then the ice maker can not call for water. This will need to be replaced but it is not easy. Just run the new wiring in place of the old wiring. Please let me know if you need anything else. Thank you for using Manage My Life.

Read More
aashe -
November 30, 2012
See more answers
Q:

My refrigerator wasn't getting water to my ice maker.

A:

Having to work on a Refrigerator can be quit a challenge. I have taken the time to research on the Manage My Life website and have found a few links that you you may find useful. While you are waiting for an expert to reply I have attached the links below. Hope the information is useful.

Read More
Priscilla V -
January 24, 2011
A:

Sometimes replacing parts can be a little tricky. The information you have received is good but does not pertain to this model. I'm attaching some pictures of the water system and hope it will help you. The connection on the outlet with the red coil will go to the filter inlet. The filter outlet will connect to the single connection going to the dual coils. The larger connection on the purple coil will go to the dispenser and the smaller connection on the tan coil will go to the icemaker. I hope this will help you. If you would like more assistance, any additional details will be helpful and I will be glad to assist you further. Thank you for using Manage My Life.

If you do not feel confident repairing this problem yourself, then you can have it repaired at your home by a Sears technician. Here is a link for the website: Sears Home Services .

Read More
Scott D -
Sears Technician
January 25, 2011
See more answers

Top Parts