Model #ED19SKXRWR1 WHIRLPOOL Side-by-Side Refrigerator

  • Cabinet
    3 Results
  • Refrigerator Door
    3 Results
  • Freezer Door
    3 Results
  • Air Flow And Control
    3 Results
  • Shelf
    3 Results
  • Unit
    3 Results
Find part by diagram >

Error Codes

Error Code:

Condition:

Check/Repair:

Question and Answers

Q:

I would like to install a new door gasket on my refrigerator.

A:

I know this type of information can be very helpful for you to have. While you are waiting for your expert answer, I did some research on the refrigerator. I was unable to locate information that would be helpful with regards to your question at this time. Your expert will answer within 24-48 hours with detailed information. Thank you for using Manage My Life. If you do decide to schedule service and have a qualified technician help you, I have also attached a link to Searshomeservices.com.

Read More
Barbara H. -
December 08, 2011
A:

Thank you for your question.

I have looked up the model number you have submitted. The door gasket on your refrigerator is secured with screws. To replace the gasket it is best to remove the door so that you can place it on a table to work. First, take everything off the door shelves. Then remove the upper hinge screws. Make sure to have a helper hold the door so it does not fall. Once the upper hinge is removed, you can lift the door off and place it on a table. If you are replacing the gasket on the freezer door, you will also need to disconnect the water line at the bottom of the door. Then click here to watch a video on how to replace the gasket.

I hope this is helpful. If you do not feel confident repairing this problem yourself, then you can have it repaired at your home by a Sears technician. Here is a link for the website: Sears Home Services .

Please let me know if you need further assistance.

Thank you for using Manage my life.

Mark T.

Read More
Mark T -
Sears Technician
December 11, 2011
A:

Thank you for your question.

I have looked up the model number you have submitted. The door gasket on your refrigerator is secured with screws. To replace the gasket it is best to remove the door so that you can place it on a table to work. First, take everything off the door shelves. Then remove the upper hinge screws. Make sure to have a helper hold the door so it does not fall. Once the upper hinge is removed, you can lift the door off and place it on a table. If you are replacing the gasket on the freezer door, you will also need to disconnect the water line at the bottom of the door. Then click here to watch a video on how to replace the gasket.

I hope this is helpful. If you do not feel confident repairing this problem yourself, then you can have it repaired at your home by a Sears technician. Here is a link for the website: Sears Home Services .

Please let me know if you need further assistance.

Thank you for using Manage my life.

Mark T.

Read More
Mark T -
Sears Technician
December 11, 2011
A:

Although this refrigerator has a freezer with a water line to the ice maker, we don't see one to the door? Should we? Can you please email us the owner's manual so that we can know more about that refrigerator. I thank you for everything you have sent. My wife agrees. It is keepin the temp between 34 to 36...It comes on and off about every 6 to 12 minutes. What is the normal range for that.

Read More
kenn209 -
December 11, 2011
A:

There are only a few holes in the gaskets, as if they are for alingment and securig. But what about the rest of the screw holes, where are they, how are we to put the hole in the right spot?

Read More
kenn209 -
December 11, 2011
A:

Thank you for the reply if your refrigerator does not have a water dispenser in the freezer door there will not be a hose on the bottom of the freezer door to mess with. I checked for the manual and it is no longer available. The temperatures in the refrigerator seem to be fine. The target temperature is 38-36. Most customers like their milk cold so I usually see temperatures from 36 to 34. The gasket will fit into the channel around the door liner. The screws just attach the liner to the door. Once the gasket is sandwiched between the two, it should not come out. If you do not want to remove all the screws, just loosen them and pull the gasket. Out. Then to install the new gasket, push the raised portion into the channel all the way around and tighten the screws.

Read More
Mark T -
Sears Technician
December 11, 2011
A:

Thanks. In other words, only the srew holes location have screws going though them. And the rest of the plates that are there just hold the plates in place, and no screw needs to go through them. Am I correct? If so, then our gaskets are a cross between the new only stick on ones, after you pull their tape, and the 100% screwed at less than 28 screws on the door.....but there must be about 6 of them on each of the 4 sides. Am I correct.?

Read More
kenn209 -
December 11, 2011
A:

You are correct the metal bars are used to secure the gasket. The screws are there just to secure the bars. There is not a video that shows how to replace the style gasket you have. The video I gave is the closest video available. Once you have the new gasket positioned, tighten the screws to secure the bars.

Read More
Mark T -
Sears Technician
December 13, 2011
See more answers

Top Parts