Model #E74 MAGNAVOX Misc Television

  • No Image Available - Fidelitone
    3 Results
Find part by diagram >

Question and Answers

Q:

Washing machine will not spin.

A:

I understand that your washing machine will not spin. While you are waiting for an expert to respond, I have attached some helpful links below that may provide information to assist you with your question. Have a great day!

Read More
Alina -
March 19, 2013
A:

Thank you for your question and I understand your concern.

Since your model washer does not have digital display window in order to display a fault/error code, the control signals the failure code by flashing the five indicator lights of Door Lock, Wash, Rinse, Final Spin and Control for the first number or letter after the E and the Start indicator light for the second number or letter after the E. 

Based on your symtom, it sounds like it may have a faulty door lock assembly. I added an image below showing how to decipher the flashing LED's. Use the information in the images below and let me know what code is flashing and then I can provide additional information. When counting the flashing LED's, cover the Start LED with one hand while counting the others or it will become confusing.

 If you get to the point where you need to have a service technician diagnose and repair this failure, you can schedule service through this link: Sears Home Services.

 

 

Read More
Joey S -
Sears Technician
March 20, 2013
A:

I have this exact model and problem along with many others if you google this. I'm amazed there are no answers. It appears to be a common problem. Sears should know the solution. The wash and rinse cycles are fine hence it is draining, but people still want to ascertain its a pump problem or motor problem. The error code is 3 beeps and that is not a pump or motor issue. When the cycle ends i hear 3 beeps. i read the manual and followed the directions to hold down cancel and start. when i do that i get 7 flashes above cancel and 4 above start. if it washes and rinses, it must mean that the motor, pump and pressure switch are working. even the control board is working for those cycles. so i am guessing if it mostly works, it has to have something to do with spin only.

Read More
Corey -
November 22, 2013
A:

Cory; Follow the instructions in the image in the thread and it should point you in the direction of the failure and steps to make.

Read More
Joey S -
Sears Technician
November 22, 2013
A:

if i get 7 flashes above cancel and 4 above start then the code is E74 and that is not in the chart. wondering if the belt is old and too loose. i took the back off and checked out the belt. i can push it in about 1 and 1/2 inches so i know it isnt tight. it does work for agitating cycles

Read More
Corey -
November 25, 2013
A:

Corey: It is not a belt issue. Are you shure its an E74 or is a E47? If it is E47, it will likely need a new door lock assembly.

Read More
Joey S -
Sears Technician
November 26, 2013
A:

thanks. i did a wash and watched the lights and the "Door Lock" light was on, so i thought maybe the door lock assembly was ok.

Read More
Corey -
November 30, 2013
A:

Corey: Just because the lock light comes on does not mean the door lock assembly is working properly. At this point, I would replace the door lock assembly and then see if will spin.

Read More
Joey S -
Sears Technician
December 02, 2013
A:

thanks for the info. just wondering if it could be the motor control board? i suspect it is either the door lock assembly or that.

Read More
Corey -
December 03, 2013
A:

Cory: It is not likely the motor control and most likely the door lock assembly.

Read More
Joey S -
Sears Technician
December 03, 2013
See more answers

Top Accessories