Model #DU1055XTVB1 WHIRLPOOL Dishwasher

  • Door And Panel Parts
    3 Results
  • Control Panel Parts
    3 Results
  • Door And Latch Parts
    3 Results
  • Fill, Drain And Overfill Parts
    3 Results
  • Tub And Frame Parts
    3 Results
  • Pump And Motor Parts
    3 Results
  • Upper Wash And Rinse Parts
    3 Results
  • Heater Parts
    3 Results
  • Upper Rack And Track Parts
    3 Results
  • Lower Rack Parts
    3 Results
  • Lower Washarm Parts
    3 Results
  • Optional Parts (not Included)
    3 Results
Find part by diagram >

Troubleshooting

Error Codes

Error Code:

Condition:

Check/Repair:

Question and Answers

Q:

error codes and self test on whirlpool dishwasher

A:

When ever there are error codes and self test available for Whirlpool dishwasher, it makes for an easy diagnose. I hope the links provided below are helpful while an expert responds to your specific model instructions.

Read More
Anna T -
December 12, 2012
A:

The instructions to enter and run the diagnostic test are in the images below. The 1st image tells how to start the test and the 2nd image shows what should happen during the test. I hope this helps. You can reply with any additional details or questions for further assistance.

Read More
Fred M -
Sears Technician
December 12, 2012
A:

I tried running this test and it will not make it thru the whole test it just shuttsoff at all different times durring the cycle when it shuttsoff there are no lights on the panel could it be the control board

Read More
Michael -
December 14, 2012
A:

the 2nd image below show the cycle chart for the test. It shows what part is turned on and for how long. Could you tell if the circulation motor ran after it filled?

Read More
Fred M -
Sears Technician
December 15, 2012
A:

My quiet partner 2 is dead. no lights, no buttons work, no reseting with pushing buttons in any sequence. Thermal fuse has continuity. Getting strange readings when checking volts at all contacts. Touch one lead with one probe and I get low voltage, then touch another lead with the other probe and voltage disappears. Can you explain problem?

Read More
305Westminster -
February 01, 2013
A:

If there are no lights and the thermal fuse is okay then I suggest you check the wire nuts connecting the house wiring to the dishwasher. Remove the kick plate to access the dishwasher junction bos. A loose wire nut or connection may be the problem. If you reply with a model number I may be able to bring up a wiring diagram for your particular dishwasher.

Read More
Fred M -
Sears Technician
February 02, 2013
A:

I took plate off and removed the wire nuts and checked with meter and didn't have any power. I then checked an outlet to make sure meter was good. I traced the power cord thinking that is was hard wired into a recepticle, and found that is was plugged into recepticle under sink. When looking at it closer, I discovered that the spray handle hose had worked the plug loose over time. I pushed plug in and my dish washer is now working.

Read More
305Westminster -
February 04, 2013
A:

Great. That is the type of problem you don't want to spend money on a service call. Great job.

Read More
Fred M -
Sears Technician
February 04, 2013
See more answers
Q:

How do I enter the test mode on my dishwasher DU1055XTVB1 Whirlpool Undercounter dishwasher

A:

When an appliance suddenly stops working it can cause an inconvenience in your home. While you are waiting for an expert to respond I was able to locate some great information that could possibly assist you with your issue. I have added the link below. Hope this helps!

Read More
Yadira B -
January 21, 2013
A:

I know that it can be very frustrating to have issues with your dishwasher. The diagnostics cycle can be very helpful when it comes to determining problems and solutions for it. The image below will provide the information you need to enter this cycle. It also includes several tips on what to look for. I hope this helps. If you need further assistance, please reply to this thread. Thank you for using Manage My Life.

Read More
AnneJ -
Sears Technician
January 22, 2013
A:

I can not see any of the links or image can someone please just tell me how to enter the diagnostic cycle I do not know why I can not see any images.

Read More
Brandon -
January 25, 2013
A:

I apologize for the issue that you are having with the images. At this moment we are having some issues getting the images to enlarge properly. The best way to view this is with your "Paint" program under your accessories on the Start Menu, or use the "Maginfier" on under the accessibility program. This is also under you accessories. If you are still having issues with the images, please let me know. Thank you for using Manage My Life.

Read More
AnneJ -
Sears Technician
January 25, 2013
See more answers

Top Parts