Model #DU1055XTST3 WHIRLPOOL Dishwasher

  • Door And Panel Parts
    3 Results
  • Control Panel Parts
    3 Results
  • Door And Latch Parts
    3 Results
  • Lower Washarm Parts
    3 Results
  • Heater Parts
    3 Results
  • Fill And Overfill Parts
    3 Results
  • Tub And Frame Parts
    3 Results
  • Pump And Motor Parts
    3 Results
  • Upper Rack And Track Parts
    3 Results
  • Upper Wash And Rinse Parts
    3 Results
  • Lower Rack Parts, Optional Parts (not Included)
    3 Results
Find part by diagram >

Troubleshooting

Error Codes

Error Code:

Condition:

Check/Repair:

Question and Answers

Q:

How do I change the door springs and friction sleeve? DU1055XTST3 Whirlpool Dishwasher

A:

Thank you for submitting your question. I understand your concern and I will be happy to assist you. This video will assist you with replacing the door spring parts. I hope this helps. Please reply back to this thread if you require further assistance. Thank you for using Manage My Life.

Read More
Tykara -
Sears Technician
October 25, 2013
Q:

Drain issue - maytag quiet partner I DU1055XTST3 Whirlpool Dishwasher

A:

I know that it can be very difficult to have issues with your dishwasher. Since you have already replaced the drain pump, the control module, and have checked the check valve, there shouldn't be anything stopping the unit from draining. The only thing that I can suggest you do is run the diagnostics cycle on the unit. It is possible that it just needs to be recalibrated. The image below will show you how to do this. If you don't feel comfortable doing this yourself, please click on this link to schedule service: Sears Home Services. Click on "Get Started" and follow the directions, click on the red "NEXT" button to continue. I hope this helps. Please feel free to let me know if you need further assistance. We are always here to help. Thank you for using Manage My Life.com.

Read More
AnneJ -
Sears Technician
September 17, 2013
A:

AnneJ-- Would you please repost the image? It does not appear. thanks so much

Read More
Scott -
September 17, 2013
A:

I am very sorry that you are unable to see the image. I have added it below, as well as a link to it just in case. Please let me know if there is anything else you need. Thank you for using Manage My Life.

Read More
AnneJ -
Sears Technician
September 17, 2013
A:

Image

Read More
AnneJ -
Sears Technician
September 17, 2013
A:

Not sure why, but neither image or link appears. I did find a method to run diagnostics - heated dry / normal / heated dry / normal but no luck. Is it possible that too much water is being dispensed into the washer? Also, what function does the "sensor" do? Thanks for your help.

Read More
Scott -
September 17, 2013
A:

I should clarify - the drain pump does run for a short time at the end of the wash cycle but it does not run long enough to drain the washer completely.

Read More
Scott -
September 17, 2013
A:

Your symptoms point to a clog or restriction in the soil settler. To check this area yourself, you will need to shut off the breaker for the dishwasher and pull it out from under the counter. Lay the dishwasher on its back and use the procedure shown at the bottom of the image to access the soil setter. NOTE: Make sure that all water is drained from the dishwasher before beginning this procedure. You may still be able to gravity drain the dishwasher into a shallow pan. If not, you can use a wet/dry shop vacuum to remove most of the water. Be prepared to catch residual water when you remove hoses and components on the bottom of the dishwasher. If you remove the soil settler, you will likely find a restriction that is preventing the dishwasher from draining properly.

Read More
AnneJ -
Sears Technician
September 17, 2013
See more answers

Top Parts