Model #DU1055XTSS2 WHIRLPOOL Dishwasher

  • Door And Panel Parts
    3 Results
  • Control Panel Parts
    3 Results
  • Door And Latch Parts
    3 Results
  • Lower Washarm Parts
    3 Results
  • Heater Parts
    3 Results
  • Fill And Overfill Parts
    3 Results
  • Tub And Frame Parts
    3 Results
  • Pump And Motor Parts
    3 Results
  • Upper Rack And Track Parts
    3 Results
  • Upper Wash And Rinse Parts
    3 Results
  • Lower Rack Parts, Optional Parts (not Included)
    3 Results
Find part by diagram >

Troubleshooting

Error Codes

Error Code:

Condition:

Check/Repair:

Question and Answers

Q:

Whirlpool control panel peel DU1055XTSS2 Whirlpool Dishwasher

A:

Thanks for your question- we see that no one from the community responded.  If you still require assistance on this topic, please resubmit your question with any updated information and we will have one of our experts take a look.  Also, we have updated our site to include information regarding common repairs and diagnosis, which can be found here: www.searspartsdirect.com/repair-help.html.  If you are looking for your owner’s manual, it can be found here: http://www.searspartsdirect.com/partsdirect/user-manuals.  Thanks for visiting SearsPartsDirect.com.”

 

Read More
Natasha12 -
Sears Technician
December 05, 2013
Q:

my dishwasher is not working at all.

A:

I understand that your dishwasher is not working at all. While you are waiting for an expert to respond, I have attached some helpful links below that may provide information to assist you with your question. Have a great day!

Read More
Alina -
March 23, 2013
A:

Thank you for submitting your question. I understand your concern and I will be happy to assist you. If the unit appears like it has no power to it, the issue could be a fuse or the control board. If the unit has blinking lights on the touch pad, then it's indicating an error message. Please reply back to this thread with more details of what's going on with your Whirlpool dishwasher for further assistance. Thank you for using Manage My Life.

Read More
Tykara -
Sears Technician
March 25, 2013
See more answers
Q:

my whirlpool dishwasher will not fill with water. I changed the inlet valve and still same issue?

A:

I know how difficult it is to have your appliances not working properly. While you are waiting for your expert answer, I have found a link that will provide some information on the issue. It includes several troubleshooting tips. I hope this will help you find the problem.

Read More
aashe -
May 27, 2011
A:

I understand how important your dishwasher is to you, at times we fix the big issues and forget to check the small things. Check to make sure that you turned back on your hot water supply.

Read More
Gfather -
May 27, 2011
A:

If the fill valve didn't fix the problem then the only two things left that might cause this problem is a bad control or float switch. The image below may help you see the potential problems.

Remember to turn the power off first.

The float is sometimes overlooked. If the float is out of position then the float switch will assume a flood and will not allow any more water to fill. Make sure the float is down the standpipe.

If the float is in position then check the float switch. You should hear a click as the float is lifted up and down.

If not the valve or float switch the the control or even a bad wire or connection might be at fault.

I hope this is a good start for you to resolve this problem. You can reply with any additional details or questions for further assistance.

Read More
Fred M -
Sears Technician
May 28, 2011
A:

Didn't hear a click when I turned on washer so should I order a new float switch?

Read More
Capt Roscoe -
May 30, 2011
A:

You should listen for the click when the float is lifted up and down. The two wires on the float switch can be removed once the power to the dishwasher is turned off and joined together to bypass the switch to see if you get a fill then.

Read More
Fred M -
Sears Technician
May 30, 2011
A:

Ok will bypass and see if I get a fill.

Read More
Capt Roscoe -
May 30, 2011
A:

Bypassed switch and no water. Checked resistance on the float switch and it is good , read .01 . I am at a stand still now , what do you think Fred?

Read More
Capt Roscoe -
May 31, 2011
A:

If the float switch and valve are not the problem they we are left with the control or a broken wire. Refer to the wiring diagram in the previous image. Broken wires are rare and I'm sure you have checked the wire connections at the valve and float switch. You might access the control by removing the console after turning the power to the dishwasher off.

Read More
Fred M -
Sears Technician
June 01, 2011
See more answers

Top Parts