Model #DS4500EB0WW GE Residential Dryer

  • Backsplash, Blower & Motor
    3 Results
  • Front Panel & Lint Filter
    3 Results
  • Cabinet
    3 Results
  • Drum
    3 Results
Find part by diagram >

Error Codes

Error Code:

Condition:

Check/Repair:

Question and Answers

Q:

Dryer door is damp when I open it and clothes are steamy. DS4500EB0WW Ge Electric dryer

A:

Thank you for your inquiry on your Ge Dryer, Model: DS4500EB0WW. From reviewing the details on your model, I have provided a link to a couple of videos on similar model of dryers, which should be able advice what other ducts you would have to clean. The link is found below.

Click Here

Safety Warning: Before beginning the repair, disconnect the direct power supply to the dryer to prevent the risk of injury or any electrical shock.

If you don’t feel comfortable or confident in this repair, then you can have it repaired at home by a sears technician. I have the included a link to the website: Sears Home Services or call 1-800-469-4663.

I hope this answered your question. Thank you for contacting SearsPartsDirect.com, and have yourself a wonderful day. 

Read More
Gerry 93 -
Sears Technician
April 13, 2015
Q:

My dryer makes a sqeeking noise when running. DPSR483EA1WW Ge Electric dryer

A:

Here is a link for a previous answer that provides an illustrated procedure for completing that repair: http://www.managemylife.com/mmh/questions/334881-ge-dryer-model-ds4500eb0ww-making-squealing-noise .

 

Unplug the dryer before accessing internal components and replacing parts.

 

If you need more help, let us know. 

Read More
Lyle W -
Sears Technician
November 05, 2013
Q:

GE dryer model DS4500EB0WW making squealing noise.

A:

It's great that you want to try and fix your dryer yourself. While you are waiting for an expert to respond I was able to locate some great information that could possibly assist you with your issue. I have added the link below. Hope this helps!

Read More
Yadira B -
February 10, 2013
A:

Thank you for your question and I understand your concern.

I suspect it could have a worn drum bearing based on your details. The drum has a shaft protruding out the back of the drum where it rides inside a plastic bearing. The bearing will likely need to be replaced. In order to access the bearing, the front panel  and drum will need to be taken out.  The drum bearing is part # WE1M462. The drum bearing can be ordered from SearsPartsDirect. 

I added an image below with the procedure for removing the drum.

Note: Disconnect the power cord from the power source before servicing.

I hope this is helpful. If I may be of further assistance as more details become available, please reply to this post.

 

 

Read More
Joey S -
Sears Technician
February 11, 2013
A:

thank you. I removed the drum and the plastic drum sleeve bearing looks ok, but there was no o-ring like it shows on diagram on searspartsdirect.com. should I just put on an o-ring & lubricate and reassemble? Or do I need to remove the heater assembly to replace the bearing retainer possibly? please see attached photos. thank you for your help. Mike

Read More
Mike -
February 16, 2013
A:

Mike: The image I provided in my last replay does not pertain to your model. Your model has a drum bearing sleeve and not the type shown in the image above. Yes, to remove and replace the drum bearing sleeve, the heater housing will need to come off. This plastic bearing installed from the front and not the rear. The drum bearing sleeve is not to be lubricated either. Be sure to check the front bearings and seal where the front of the drum rides on the front bulkhead for any wear too.

Read More
Joey S -
Sears Technician
February 18, 2013
See more answers

Top Parts