Model #DEGX1-96010B FISHERPAYKEL Residential Dryer

  • Top Deck And Electronics
    3 Results
  • Cabinet/drum/inlet Duct
    3 Results
  • Outlet Duct
    3 Results
  • Chassis/motor Assembly
    3 Results
  • Subdeck/drum Door Assembly
    3 Results
  • Base Panel
    3 Results
Find part by diagram >

Question and Answers

Q:

oval blue replace part DEGX1-96010B

A:

Thank you for choosing SearsPartsDirect.com and being a valued member.  I can certainly understand how frustrating it can be when your dryer is not heating.

 I have attached the instructions to assist you in testing the parts that go with your dryer's heating circuit. 



 You can also visit searpartsdirect.com for parts, diagrams, and repair information.

 

If you do not feel confident repairing this problem yourself, then you can have it repaired at your home by a Sears technician. Here is a link for the website: Sears Home Services .

Thank you for your question. Have a great day.

SAFETY NOTICE: Be sure to disconnect power to the appliance before performing any repairs. If you are not comfortable with doing any voltage checks that might be recommended, please contact your local service provider for repairs. Be aware that there could be sharp edges inside the appliance that could cause cuts or other injuries to yourself or others.

Read More
Natasha12 -
Sears Technician
June 16, 2015
A:
Natasha12 -
Sears Technician
June 16, 2015
See more answers
Q:

FisherPaykel DEGX1-96010B; What is the procedure to replace Drum Bearing? DEGX196010B Fisherpaykel Dryer

A:

 

Thank you for choosing Searspartsdirect.com and being a valued member. I can certainly assist you in locating the instructions to replace the drum bearing on your dryer. 




6.1 Removal of Lid
(a) Open the lid fully, then lift off vertically.

6.2 Components in Console Area
(a) Disconnect the unit from the power supply.
(b) Remove the lid. (Refer to Section 6.1)
(c) Remove the two screws at the rear of the console
securing the console to the top deck.
(d) Tilt the console forward.

6.3 Removal of Display Module
(a) Follow instructions for removal of the console. (Refer
to Section 6.2)
(b) Disconnect the wiring harness from the display
module.
(c) Push the tab clear and slide the module.
(d) Lift the display module clear of the console.

6.4.1 If the top deck is to be removed for replacement:
(a) Follow instructions for removal of the console. (Refer to Section 6.2)
(b) Disconnect the wiring harness from the display module.
(c) Carefully remove the two lid buffers from the front side top of the deck by levering upwards, taking care not to damage the top deck.
(d) Remove two screws under the buffers securing the top deck to the cabinet.
(e) Tilt the top deck upwards towards the rear.
(f) Disconnect the wiring harness from the sensor module
and lift the top deck clear.
(g) Remove the top deck harness from the top deck.
(h) Remove the lid lock, complete with harness, from the top deck. (Refer to Section 6.5)
(i) Remove the stiffener brackets from under each side of the top deck.

6.6 Components Within Cabinet
(a) Follow instructions for removal of the top deck. (Refer to Section 6.4.2)
(b) Remove the two screws securing the top of the front panel.
(c) Spread the top sides of the front panel to clear the tabs on the door grabber assembly.
(d) Pull the cabinet front forward and lift the base clear of the feet.
(e) Disconnect the cabinet front earth wire from the chassis and lift the cabinet front clear.

6.7 Removal of Front Cabinet Brackets
(a) Follow general servicing instructions for components within the cabinet. (Refer to Section 6.6)
(b) Invert the cabinet front.
(c) Remove the screw securing the bracket to the cabinet front.
(d) Prise the retaining clip upwards.
(e) Slide the bracket inwards then to the rear to clear the cabinet front.
Reassembly
(a) Refit in reverse manner.
6.10 Removal of Door Grabber
(a) Follow instructions for removal of the door grabber
actuator assembly. (Refer to Section 6.9)
(b) Remove the four screws securing the chassis beam to the
grabber housings.
(c) Lift the door grabber clear.
Reassembly
(a) Refit in reverse manner. Ensure that the linkage is
correctly located in the slot of the door grabber.

6.16 Removal of Drum and Chassis Assembly
(a) Follow general servicing instructions for components within the cabinet. (Refer to Section 6.6)
(b) Follow instructions for removal of the door grabber assembly. (Refer to Section 6.8)
(c) Remove the lid from the motor control module by pushing the clip on lid, lifting the front of the lid
and sliding forward.
(d) Disconnect the earth wire from the outlet panel chassis to the base panel.
(e) Disconnect the earth wire from the motor harness to the base panel.
(f) Unplug the motor harness from the motor control module.
(g) Unplug the 6 wire communication harness from the motor control module.
(h) Lay a protective mat on the floor in front of the dryer.
(i) Pull on the front of the panel chassis to pivot the assembly out of the cabinet.
(j) Roll the assembly clear of the cabinet.

6.25 Removal of Inlet Panel Assembly
(a) Follow instructions for removal of the drum and chassis assembly. (Refer to Section 6.16)
(b) Manually open the drum door.
(c) Remove the drum inlet bearing. (Refer to Section 6.28)
(d) Lay the assembly on its left hand side.
(e) Remove the belt tensioner. (Refer to Section 6.24)
(f) Remove the chassis panel bracket.
(g) Remove the screws holding the chassis beams to the inlet panel, 2 from the front of the inlet
panel assembly (photo 1), 2 from the rear of the inlet panel assembly (photo 2) and 2 from
underneath the inlet panel assembly.
(h) Lift the inlet panel assembly clear.
Reassembly
(a) Refit in reverse manner. Do not overtighten the screw securing the drum inlet cap. Tighten to 7
newton metres (1.5 foot pounds).


6.27 Removal of Inlet Bearing Shaft
(a) Follow instructions for removal of the inlet panel assembly.
(Refer to Section 6.25)
(b) With a deep bore 22mm (7
/
8”) socket, unscrew the inlet
bearing shaft and remove.
Reassembly
(a) Refit in reverse manner. Before refitting the inlet bearing
shaft, ensure that the inlet bearing spacer is in position on
the bolt between the inlet duct front panel and the inlet
duct back panel. Tighten to a torque of 20 newton metres
(15 foot pounds).
6.28 Removal of Drum Inlet Bearing
(a) Lift the lid./
(b) Remove the drum inlet bearing cap by
unscrewing with a M5 or 3
/
16” Allen key.
(c) Remove the 5 screws securing the bearing
retainer to the drum and remove the retainer.
(d) While lifting the drum slightly, slide the bearing and
housing off the shaft.
Reassembly
(a) Refit in reverse manner. Ensure that the bearing housing
is orientated so that the rivet heads sit in the clearance holes. Lift the drum upwards while sliding
the bearing onto the shaft. Do not overtighten the screw securing the drum inlet cap. Tighten to
10 newton metres (7 foot pounds).

You can also visit searpartsdirect.com for parts, diagrams, and repair information.

If you do not feel confident repairing this problem yourself, then you can have it repaired at your home by a Sears technician. Here is a link for the website: Sears Home Services .

Thank you for your question. Have a great day. 

Read More
Natasha12 -
Sears Technician
November 24, 2014
Q:

Fisher and Paykel DEGX1 - 96010-A Heating problem DEGX1-96010B Fisherpaykel Dryer

A:

Thank You for choosing Sears PartsDirect.com and being a valued member. It is unfortunate to hear that you are having issues with your dryer and I do understand your frustration. Glad to help out. I'm looking at your model number degx1-96010b and from your description I suspect that the upper auto reset thermostat part number 395668 and the sensor module part number 395394p. I have included a link to our PartsDirect page where you can purchase the part you need to complete your repair. Just click the blue link above to be taken to the page. I trust this information will help you.

 

Thank you for choosing Sears PartsDirect.com.

 

SAFETY NOTICE: Be sure to disconnect power to the appliance before performing any repairs. If you are not comfortable with doing any voltage checks that might be recommended, please contact Sears for repairs. Be aware that there could be sharp edges inside the appliance that could cause cuts or other injuries to yourself or others.

Read More
Sherman_G_Wallace -
Sears Technician
October 07, 2014