Model #D20 AMANA Upright Freezer

  • (16) (20) (25c) (25sc)
    3 Results
  • Door Assembly (16) (20) (25c) (25sc)
    3 Results
  • (d13) (d20)
    3 Results
  • (fs16) (s16) (s20) (s25)
    3 Results
  • Liner Assembly (fs16)
    3 Results
  • Hinge Bearing Arrangement (d13) (d13l) (fs16) (fs16l) (d16) (d16l) (s16) (s16l) (d20) (s20) (s25)
    3 Results
  • Cabinet And Refrigeration Assembly (d13) (d13l) (fs16)
    3 Results
  • Cabinet And Refrigeration Assembly (d13) (d13l) (d23)
    3 Results
  • (d13a) (ff16) (d18) (s20a) (d23) (d23a)
    3 Results
  • Door Assembly (ff16) (s20a)
    3 Results
  • Door Assembly (ff16) (d18) (d23) (d23a)
    3 Results
  • Liner Assembly (ff16)
    3 Results
  • Cabinet And Refrigeration Assembly (ff16)
    3 Results
  • Cabinet And Refrigeration (ff16)
    3 Results
  • Comprssor Terminal Section (d13a) (d13c) (ff16) (ff16a) (d18) (d18b) (s20a) (d23) (d23a)
    3 Results
  • Drain Parts Section
    3 Results
  • 3 Results
Find part by diagram >

Question and Answers

Q:

Belt too long? 11072974103 Kenmore Gas dryer

A:

Thanks for the inquiry and for being a valued member.

Based upon the dryer model of 110.72974103, the dryer repair kit of 4392067 is the correct kit. If the belt seems too long, it is probably not routed correctly around the idler and motor pulley. I have provided an image below to show the routing of the belt. 

Image result for kenmore dryer belt routing

There are also some great YouTube videos you can watch to see how the belts are installed and routed. 

I hope this helps and thanks for using SearsPartsDirect.com. We appreciate your business. 

Read More
Jeff Wallace Sr -
Sears Technician
March 02, 2015
Q:

I have a GE Dishwasher, model GSD2800. I receive a message that the arm is blocked but it spins freely. Thanks

A:

I am sorry that you are having some difficulties with your dishwasher. I did some research on the unit and I was unable to locate information that would be helpful with regards to your question at this time. Your expert will answer within 24-48 hours with detailed information. Thank you for using Manage My Life.

Read More
Joseph P. -
September 24, 2012
A:

Hi,

Thank you for your question. It is concerning when your appliance is not functioning correctly.

There is a reed switch that sees a magnet built in the spray arm, as the arm turns the reed switch closed a circuit and the motor keeps on running in wash. If the sensor or the magnet fails the blocked spray arm error is emitted. You could check the spray arm ends to see if the magnet is still operating. It is a magnet and will react to metal, so the magnet can be checked by holding something metal around the ends of the spray arm. If the metal sticks to the spray arm, you have a sensor problem. See Pictures

I hope this is helpful. If I may be of further assistance please include more details in a reply to this entry below.
Thank you for using Manage My Life.

Read More
Bill__W -
Sears Technician
September 26, 2012
A:

Thank you very much, Mr. Bill. Will test the magnetism this weekend. Approximately how much will it be to fix the sensor?

Read More
marmol -
September 28, 2012
A:

The price for the sensor is part number WD21X580 at a cost of 37.99 + tax and shipping if any where you are at. The spray ary is WD22X135 at a cost of 74.99 + ship and handling. If a sears tech came to repair the diswasher sensor, the dw would have to be pulled out and the sensor replaced and tested. This would run 200.00 to 250.00. high side.

Read More
Bill__W -
Sears Technician
September 29, 2012
A:

Thank you very much, Mr. Bill! The magnet is working so I guess it is a sensor problem. Since the d/w is 20-25 years old, I think I'll look for a replacement. I very much appreciate your timely replies!

Read More
marmol -
October 01, 2012
A:

You are Welcome.

Read More
Bill__W -
Sears Technician
October 02, 2012
A:

After enduring the same error message every minute during the wash cycle (GD2800D03) and trying MANY different "cures" (even to replacing the pump assy and adding teflon gaskets), I made a tight fitting plexiglass shield and defeated the interlocks so I could watch the operation. The lower arm jets were no longer spraying in the proper direction (or even the same direction) to drive the arm, probably due to the MANY years of extremely caustic dishwasher solution eroding the plastic. Although I could use JB weld and rebuild the jet orfices, I have a new arm WD22X135 on order. Wish I had done the plexiglass shield years ago. . .

Read More
Jim -
October 02, 2012
See more answers
Q:

I need an update for my embroidery machine.

A:

I am sorry that you are having some difficulties finding information about your embroidery machine and I will be happy to help. I suggest you add to the thread of this question and include the full and correct model number of your machine so that the expert can provide you with a more detailed answer. I did some research and I was able to find two links that will provide you with some good information. I hope this helps while you wait for your expert response.

Read More
Joseph P. -
April 28, 2012
A:

I'm sorry I think you misunderstood. I don't need the customizer, it still works fine, although some lessons would be helpful. My problem is the program on the machine itself. The update erased everything, it won't sew at all.

Read More
Patty -
April 28, 2012
A:

Thank you for your question on the software update.

If you are looking for an update to the electronics on the sewing machine, I am sorry but there is none. And trying to put the Janome software update in will not work.

If you have erased the software in the machine you will need to take it to a Sears repair center and they may have to install a new A main control board.

The new A board is about $264.00 plus labor.

I am so sorry that this happened.

Thank you.

Sam A.

Read More
Sam A -
Sears Technician
April 30, 2012
See more answers