Model #CWE5800ACE MAYTAG Built-In Oven, Electric

  • Control Panel
    3 Results
  • Oven (cwe5800acb/ace)
    3 Results
  • Body (cwe5800acb/ace)
    3 Results
  • Door
    3 Results
  • Door-lower (cwe5800acb/ace)
    3 Results
  • Wiring Information
    3 Results
Find part by diagram >

Question and Answers

Q:

Oven heats slowly. CWE5800ACE Maytag Oven

A:

Thanks for the inquiry and for being a valued member.

I am sorry to hear of the prolonged period of time it takes for the upper oven to heat. I know how frustrating that is to have happen.

The oven internal heating and temperature is controlled by two components, the oven temperature sensor and the electronic control. 

It's likely you have a defective oven temperature sensor, but it should be checked for resistance before replacing. At room temperature, it should measure about 1100 ohms. If it doesn't, I would recommend replacing it with part number 12001656. If it does test right, you will need an electronic control board, part number 7601M285-60R. 

I hope this helps and thanks for using SearsPartsDirect.com. We appreciate your business. 

Read More
Jeff Wallace Sr -
Sears Technician
November 05, 2014
Q:

how to replace maytag cwe5800 wall oven door springs CWE5800ACE Maytag Oven

A:

Thank you for choosing Sears Parts Direct. I can certainly assist you in locating the instructions to replace the wall oven door springs. I did look into the model number you have provided and I have found information to assist you.

To lift off the door:
1. Open the door to the broil stop position. About 4-6 inches
2. Grasp both sides of the door and lift up until the door clears the hinges.
Caution: The hinge arms are spring loaded and may slam shut. Do not place  hand or fingers between the hinge and front frame of the oven. 
This should be able to assist you in getting in contact with the springs. 

Let me know if this helps.

 
You can also visit searpartsdirect.com for parts, diagrams, and repair information.
 
 
If you do not feel confident repairing this problem yourself, then you can have it repaired at your home by a Sears technician. Here is a link for the website: Sears Home Services.

Thank you for your question. Have a great day. 

Read More
Natasha12 -
Sears Technician
May 07, 2014
Q:

wiring harness

A:

I can certainly, understand how important it is to have one of our major appliances working properly. I have done some research and located a link similar to your question that may be helpful until an Expert responds. Hope this helps and thank you for choosing Manage My Life!

Read More
Carmen G -
September 13, 2012
A:

The first image below shows the wiring diagram for that oven. There may be some revisions depending on your serial number. The first 2 digits of the serial number indicate your "Series" number. That original model (Series 10) wiring changed slightly at Series 21 and Series 24. The exact wiring for your range may be slightly different than the wiring that is shown in the first image depending on your Series. The second image shows the basic procedure for accessing components. Be sure that you shut off the house circuit breaker for the oven before accessing internal components. You will need to pull the oven out of the cabinet to access and replace that wiring harness. Pay close attention to how the original harness is connected. You can remove and replace wire harness connections one at a time to connect the new harness. I hope that this general information helps. If you need more assistance, reply with additional details.

If you get to the point where you need to have a service technician replace that wire harness, you can schedule service through this link: Sears Home Services .

Read More
Lyle W -
Sears Technician
September 14, 2012
See more answers

Top Parts

  • CLIP

    Part: WP7112P094-60

    $ 5.81

    In Stock