Model #CRG9800AAB MAYTAG Free Standing, Gas

  • Control Panel
    3 Results
  • Top Assembly
    3 Results
  • Body
    3 Results
  • Oven/base
    3 Results
  • Gas Controls
    3 Results
  • Door/drawer
    3 Results
Find part by diagram >

Question and Answers

Q:

gas leak from stove top CRG9800AAB Maytag Maytag cooking

A:

Thank you for contacting SearsPartsDirect.com with your question about your Maytag Range. I am so sorry to hear there is a gas leak from the stove top. Because of the dangers of a gas leak, I recommend you turn off the gas supply if you can do that safely. Then contact your local gas company or a qualified technician to find the leak and correct the problem for you. 

Here at SearsPartsDirect.com we do not give advice on how to locate and correct a gas leak. Unless conducted properly, a search for a gas leak can result in serious injury and/or property damage. We love to help you with your repairs, but our expert opinion is that gas leaks should not be a do-it-yourself project. Thank you for your understanding in this matter. I hope we can help you with any future repair projects. Thank you for choosing Sears, we appreciate your business. 

Read More
Rachel Morgan -
Sears Technician
February 19, 2014
Q:

range model crg9800aab no oven heat bake or broil clock works fine stove top fine how to troubleshoot

A:

I'm sorry to hear that you are having some difficulties with your Range. I did some research for you at Managemylife.com and found an expert answer to a similar question that may help until your expert can respond to your specific question. The link is attached below. If you do decide to schedule service and have a qualified technician help you, I have also attached a link to Searshomeservices.com. I hope these links provided assist you.

Read More
James -
October 12, 2011
A:

A failure of the bake and broil burners points to a bad clock control board, a bad safety gas valve or a wiring failure in the oven circuit. The safety gas valve is the most suspect component given these details. I recommend that you check to see if the bake igniter glows when you set the oven in the bake mode. Check the broil igniter in the broil mode. If neither of those igniters is glowing, you can unplug the range and check the continuity through the safety gas valve for the bake and broil circuits. You should measure about 1.5 ohms of resistance through that gas valve using a volt/ohm meter. If that valve is "open" (measures Ol -- open load or infinite resistance) then it will need to be replaced. I recommend that you have a service technician replace that valve. Here is a link for the Sears Service website: Sears Home Services . If the safety gas valve is okay and the wiring connections are okay, then you will probably need to replace the clock control board in the console. A technician would normally check the voltage going out of that control board to the bake and broil circuits before replacing that control. I do not recommend that you check that live voltage yourself unless you are completely confident that you can safely complete that type of voltage check. Wearing protective rubber gloves during that voltage check is necessary to complete that type of check. If that control board is bad, it will need to be replaced. You can order parts from the Sears PartsDirect website.

If the igniters glow but the burners will not light, then you could have a problem with the igniters or the safety gas valve. You would need to check the amp draw through the circuit using a clamp-on ammeter. The basic theory of operation for the ignition circuit in your range is shown in the image below. If the igniter is glowing but the resistance of that igniter does not decrease to a point where the minimum 2.5 amps is flowing through that circuit, the safety gas valve will not open. If the amperage through that circuit is 2.5 amps or higher, then the safety gas valve would need to be replaced. It is rare for 2 igniters to fail at one time but it is possible.

You can order parts from the Sears PartsDirect website.

These tips may help you determine the cause of your oven heating problem. If you need more assistance, reply with additional details.

Read More
Lyle W -
Sears Technician
October 13, 2011
See more answers