Model #CLSUP IN-SINK-ERATOR Dishwasher

  • Front Panel Unit
    3 Results
  • Front Panel (cl3000 Only)
    3 Results
  • Control Panel I (clsup700/700r/400)
    3 Results
  • Control Panel Ii
    3 Results
  • Control Panel Iii (cl3000 Only)
    3 Results
  • Control Panel/inner Door
    3 Results
  • Circa-dry Unit
    3 Results
  • Fill And Overfill Unit
    3 Results
  • Wash And Drain Pump Unit
    3 Results
  • Lower Wash Arm And Strainer
    3 Results
  • Heat Unit
    3 Results
  • Upper Wash/rinse Unit
    3 Results
  • Door And Latch Units
    3 Results
  • Door And Latch Unit
    3 Results
  • Frame And Misc. Items
    3 Results
  • Top And Side Panel Kits
    3 Results
  • Top And Panels (clp 400-2)
    3 Results
  • Caster Unit (clp 400-2)
    3 Results
  • Fill Hose And Cord (clp 400-2)
    3 Results
  • Upper Rack And Track (cl700r)
    3 Results
  • Upper Rack And Track I (cl700)
    3 Results
  • Upper Rack And Track Ii
    3 Results
  • Upper Rack And Track Iii
    3 Results
  • Lower Rack Unit
    3 Results
Find part by diagram >

Troubleshooting

Question and Answers

Q:

insinkerator dishwasher model # clsup-2 CLSUP-2 In-sink-erator Dishwasher

A:

Thank you for your qeustion.  I am sorry for the problem with your Insinkerator Dishwasher.  This model has a motor that runs one direction to wash and reverses direction to drain.  If the motor does not run in the drain cycle then likely the timer is at fault.  If the motor will wash then the motor is likely okay.  If the motor reverses and runs in the drain cycle but does not drain then the drain impeller 51391 is likely the problem.  The impeller51391  is no longer available as a part.  I believe you should start shopping for a replacement.  I hope this helps.  You can reply with any additional details for further assistance. 

Read More
Fred M -
Sears Technician
November 03, 2013
Q:

Insinkerator CLSUP-3 dishwasher: How to remove top drawer

A:

Managemylife.com is a great place to find the answers to just about anything, especially on appliances. I would suggest that you provide a little more information such as the make and complete model number of your product so your expert will be able to provide you the best possible answer. Just click on reply below where you can provide the additional information.

Read More
Alina F. -
November 08, 2011
A:

I did. It's an Insinkerator (make) CLSUP-3 (complete model number).

Read More
Jenn -
November 08, 2011
A:

This is an older unit and there's not a lot of information available in the way of pictures or video.

The rail should have a bumper in the front held on by a retainer. Check the image below and see if it matches what you have.

You can reply with any additional details or questions for further assistance.

Read More
Fred M -
Sears Technician
November 08, 2011
A:

Thanks Fred. I do have the bumper and retainer...I can't quite figure out how to take them off. Will that even help to screw back in the part I'm referencing? on the picture you uploaded, it looks to me like part 15 has come unscrewed from part 17 and I can't figure out how to screw it back in.

Read More
Jenn -
November 12, 2011
See more answers
Q:

we own a insink erator dishwasher and its model number is clsup2 and the serial number is EJ013731 and all of a sudden when i hit start nothing happened

A:

Dishwashers can be difficult to troubleshoot. While you wait for the expert, you can check a troubleshooting guide from another web site if you wish. I attached below. If you would like to schedule a technician to do the diagnosis and repair, an option is the Sears Home Services scheduler below.

Read More
Barbara H. -
June 17, 2011
A:

From the description you give I suspect there is a power problem or the timer is bad.

Are there any lights at all?

This is an older dishwasher and some parts like the timer are no longer available.

If there are no lights and the unit is completely dead I'd suggest checking the electrical box of the dishwasher behind the lower access panel. Turn the power to the unit off first.

The house wiring is usually connected to the dishwasher wiring with wire nuts. Check and tighten the connection.

If not a connection problem then I suggest it is time to go shopping. The most likely bad part is no longer available.

Check out some new dishwasher choices at the following link: New Dishwashers .

I hope this helps. Hopefully you have a loose wire nut. You can reply with any additional details for further assistance.

Read More
Fred M -
Sears Technician
June 20, 2011
See more answers