Model #C12 SHOP VAC Carpet/Floor Sweepers

  • Unit Parts
    3 Results
Find part by diagram >

Question and Answers

Q:

i nee x to drill a whole on g he side of my freezer im i going to hit any wires c12j

A:

Thank you for choosing Sears Parts Direct. I will be more than happy to help with your refrigerator. Most manufactures do not recommend that you drill through the cabinet since there are some electrical wires and sometimes coolant lines that run through the sides of the unit.

I trust this information will help you, we appreciate your business thank for choosing Sears.

Read More
CarlosZ -
Sears Technician
April 01, 2015
Q:

Kenmore Wall furnace -- Gas valve/Pilot adjustment button 867758160 Kenmore Wall furnace

A:

The gas control valve assembly will need to be replaced. I added a link where you can purchase the gas control valve assembly part number 36C12-310. I would not attemp to repair your faulty gas control valve assembly.

I hope this is helpful. The valve is expensive so you may consider replacing the wall furnace rather than replacing the gas control valve assembly.

Read More
Joey S -
Sears Technician
November 11, 2014
Q:

wash cycle doesent start 417 44252501

A:

Thanks for the inquiry and for using SearsPartsDirect.com.
I am sorry to hear of the error you are having with the Kenmore washer, I know how frustrating those types of issues are to have occur.
The flashing you see from the start LED is a part of an error code that the machine is experiencing. Here is how it works:

Model differences:
•Better models have a digital readout display
•Good models do not have a digital readout display
In the Better Models line, the failure codes will appear in the display as an E followed by two numbers, a number and a letteror two letters. The control will beep and the Door Lock, Wash, Rinse, Final Spin and Control indicator lights will flash.
 
Example:E14. To stop the flashing and beeping, the customer may touch the
Pause Cancel
button. The error code remainsstored in the control but once the problem is corrected, it does not effect the operation of the washer. If the failure is somethingthat the customer can correct (such as the water faucets being turned off), the washer will operate normally the next time it isstarted.
In the Good Models line, the control signals the failure code by flashing the five indicator lights of Door Lock, Wash, Rinse,Final Spin and Control
for the first number or letter after the E and the Start
indicator light for the second number or letter after the E. When a failure occurs, the washer stops or pauses and the control beeps and flashes the five indicator lights to tellthe customer that a failure has occurred. To stop the flashing and beeping, the customer may touch the Pause Cancel button.The error code remains stored in the control but once the problem is corrected, it does not effect the operation of the washer.If the failure is something that the customer can correct (such as the water faucets being turned off), the washer will operatenormally the next time it is started.
To recall an error code,
•Wake the machine by pressing any button
•Wait 5 seconds
•Press and hold the Start and Pause Cancel buttons simultaneously
•All LEDs will go blank and after a few seconds the control will signal the stored code using audible beeps and blinkingLEDs. The control will repeatedly signal the code, as long as the Start and Pause Cancel buttons are pressed.A two-second pause between repeats affords you the ability to make accurate counts to identify the correct error codes.
Please Note the following...... on a small number of washers with serial number prefix XC4,if the previous procedure does not perform as specified, follow the option below:
•Follow all previous steps but instead of pressing Start and Pause Cancel buttons,press and hold Options and Pause Cancel buttons.
If the washer is a Better Model, the error code will appear in the display. Troubleshoot problem by using charts on thefollowing pages.If the washer is a
Good Model, the five indicator lights of Door Lock, Wash, Rinse, Final Spin and Control will flash thenumber of times for the first digit of the code and the Start indicator light will flash the number of times for the second digit.Take separate counts of each indicator light, then repeat to confirm in order to be accurate in identifying the proper error code.The code is obtained by counting the number of times the lights flash. Example E24: The five indicator lights would flash twiceindicating the 2 and the START indicator light will flash four times indicating the 4. The five indicator lights and the START indicator light start flashing at the same time.The control will pause for 2 seconds, then repeat the code as long as the two buttons are pressed and held.
Note:A letter appearing in the code standsfor a number higher than nine:A = 10B = 11C = 12D = 13E = 14F = 15
Example Code F1: the first digit would be 15 and the second digit would be 1. If this code would appear on a washer in the Good model line, the five indicator lights would blink fifteen times and the START indicator light would blink once. 
Once the fault code is identified, you can go online and plug it in to see what it means, or you can submit another question and have us assist. Hopefully this helps.
Thanks for using SearsPartsDirect.com. 

Read More
Jeff Wallace Sr -
Sears Technician
February 24, 2014