Model #B30 HORIZON Cycle

  • Bike Assembly
    3 Results
Find part by diagram >

Question and Answers

Q:

Screen Keeps Flickering LED32B30RQ Rca Led television

A:

Thank you for being Sears’ valued member and for contacting SearsPartsDirect.com with your question about your television. I am so sorry the screen keeps flickering. I know the TV is a key part of our daily lives and know you want to get it fixed quickly. In this case, I recommend you have the TV repaired by a qualified technician.

We do not give diagnostic or repair advice on televisions because internal components in the TV can retain a dangerously high electrical charge, even when the TV is disconnected from the power supply. Here at SearsPartsDirect.com we love to help you with your home repairs but in this case, for your safety, we recommend you have the TV serviced. To set up service go to www.SearsHomeServices.com or call 1-800-469-4663 (1-800-4MY-HOME).  

Thank you for your understanding in this matter. I hope we can help you with any future repairs. Thank you for choosing Sears, we appreciate your business. 
 

Read More
Rachel Morgan -
Sears Technician
February 24, 2015
Q:

Garage door. Reprogrammed keypad and now two remotes do not work and cannot be reprogrammed 139.53918d

A:

Hello glad to help.  Thank You for choosing Sears PartsDirect.com
 
I am sorry and do understand your frustration when there is problems with the garage door opener remotes.
 
Glad to help out.   Im  looking at your Craftsman Garage Door opener model number 139.53918d.

1.  Remote control batteries may be dead.   May need to check and get new batteries.

2.  Remote control may not be sending a signal.  

3.  Lock switch is "ON".  Check for a blinking light on th Multi-function control panel.  If so then push lock button to turn OFF.

4.  Code remote control to receiver:   
A ->  Press and release the leaned button on the control motor unite.  The learn indicator light shoud glow steadily for 30 seconds.

B->  With in the 30 seconds, press and hod the button on the hand held remote.

C->  Release the button when the motor unit light starts blinking.  It has now learned the code.  If your light bulbs are not installed, then 2 clicks will be heard.

Please "RESUBMIT YOUR QUESTIONS IF THERE IS ANY OTHER PROBLEMS".
 
Thank you for your understanding in this matter and I hope we can help you with your future questions and repairs.  Thank you for choosing Sears and using our SearsPartsDirect.com.
 

Read More
Larry L -
Sears Technician
May 21, 2014
A:

Hi Larry and thanks for the answer. I should have added that to my question, but yes, batteries are good, lock switch is not ON, followed the procedure listed in the manual. However, thanks to another post, I believe I found the issue. The capacitor on the remote apparently needed to be adjusted, or the remote needed to be programmed first and then the key pad (I did both at the same time so not sure which one worked). The capacitor can be adjusted through a small hole in the back of the remote (the sticker is covering it). If you open the remote, the hole can be seen and it lines up with the back of the capacitor where a hex screw is accessible. Apparently this adjusts the frequency of the remote to make it match the received (as it apparently can drift over time). Hope this helps somebody else with the same problem (apparently common with Craftsman garage door openers).

Read More
xavier -
May 21, 2014
See more answers
Q:

Garage door. Reprogrammed keypad and now two remotes do not work and cannot be reprogrammed 139.53918d

A:

Hello glad to help.  Thank You for choosing Sears PartsDirect.com
 
I am sorry and do understand your frustration when there is problems with the garage door opener remotes.
 
Glad to help out.   Im  looking at your Craftsman Garage Door opener model number 139.53918d.

1.  Remote control batteries may be dead.   May need to check and get new batteries.

2.  Remote control may not be sending a signal.  

3.  Lock switch is "ON".  Check for a blinking light on th Multi-function control panel.  If so then push lock button to turn OFF.

4.  Code remote control to receiver:   
A ->  Press and release the leaned button on the control motor unite.  The learn indicator light shoud glow steadily for 30 seconds.

B->  With in the 30 seconds, press and hod the button on the hand held remote.

C->  Release the button when the motor unit light starts blinking.  It has now learned the code.  If your light bulbs are not installed, then 2 clicks will be heard.

Please "RESUBMIT YOUR QUESTIONS IF THERE IS ANY OTHER PROBLEMS".
 
Thank you for your understanding in this matter and I hope we can help you with your future questions and repairs.  Thank you for choosing Sears and using our SearsPartsDirect.com.
 

Read More
Larry L -
Sears Technician
May 21, 2014