Model #B16 MTD Walk Behind Lawnmower, Gas

  • Lawn Mower
    3 Results
Find part by diagram >

Question and Answers

Q:

push mower trouble 11a b16m029

A:

Thanks for your question- we see that no one from the community responded.  If you still require assistance on this topic, please resubmit your question with any updated information and we will have one of our experts take a look.  Also, we have updated our site to include information regarding common repairs and diagnosis, which can be found here: www.searspartsdirect.com/repair-help.html.  If you are looking for your owner’s manual, it can be found here: http://www.searspartsdirect.com/partsdirect/user-manuals.  Thanks for visiting SearsPartsDirect.com.

Read More
Natasha12 -
Sears Technician
May 13, 2014
A:

Thanks for your question- we see that no one from the community responded.  If you still require assistance on this topic, please resubmit your question with any updated information and we will have one of our experts take a look.  Also, we have updated our site to include information regarding common repairs and diagnosis, which can be found here: www.searspartsdirect.com/repair-help.html.  If you are looking for your owner’s manual, it can be found here: http://www.searspartsdirect.com/partsdirect/user-manuals.  Thanks for visiting SearsPartsDirect.com.

Read More
Natasha12 -
Sears Technician
May 13, 2014
See more answers
Q:

Hot magnetic strips

A:

Fully understanding your refrigerator can be difficult when your not a technition. Below I attached some linsk that will be able to help you out with your concern. I hope this helps!

Read More
Jackie S -
June 19, 2011
A:

The center section between the freezer and refrigerator is prone to the formation of condensation. Water will form and drip which is a nuisance.

To prevent the formation of condensation the strip is heated. This can be done two ways. One with a low voltage foil heater and the other is with a condenser coil.

It is normal to feel this panel get hot.

If the condenser fan you replaced is not working then the coils certainly get hotter. They will also get hotter if the coils are covered with lint.

As long as the fans are working and the unit is cooling well then there is most likely no problem.

Read More
Fred M -
Sears Technician
June 20, 2011
A:

Both sides of my Kenmore side by side (model number 106.44323400) are not getting cold enough. Compressor is running but condenser fan doesn't always run. I replaced the fan because I thought that was the problem. Now I know it is that the fan is not always getting the electricity it needs to run (does it overheat? ) what needs to be done to get the fridge and freezer colder if this is the problem? Does it have to do with the white/red wire running from the fan to electric control box?

Read More
hilda mckelvy -
July 06, 2011
A:

The condeser fan should run when the compressor is running. When it does run are the condenser coils hot?

Read More
Fred M -
Sears Technician
July 06, 2011
A:

No, condenser coils are not hot.

Read More
hilda mckelvy -
July 06, 2011
A:

That is not a good thing. If the condenser coils are not hot the there is a sealed system problem. Sealed system problem are not easy or cheap to fix. I would suggest a technician check and repair this problem.

Read More
Fred M -
Sears Technician
July 06, 2011
A:

I checked again, and they are hot. I had never really pressed my fingers against them. I wouldn't hold my fingers on them longer then 2 sec. (I think the condenser coils are the black metal that is easiest to touch behind the toe-kick.

Read More
hilda mckelvy -
July 06, 2011
A:

The coils being hot is good. Check the condenser fan by the compressor. It must be working for the unit to cool. Is there any frost build up in the freezer? Can you tell if the freezer fan is work? Is the freezer cold or cool at all or is it warm?

Read More
Fred M -
Sears Technician
July 09, 2011
A:

Condenser fan runs when I first plug in refrigerator. Eventually it stops running but compressor is still running. There is no frost build up in freezer. We pulled off the back panel of freezer and everything looks to be working fine. Coils are freezing evenly, there are no chunks of ice and fan is working. Freezer get to B/w 16-23 degrees.

Read More
hilda mckelvy -
July 11, 2011
A:

If the condenser fan stops running while the compressor continues to run then the condenser fan motor is bad.

Read More
Fred M -
Sears Technician
July 11, 2011
See more answers
Q:

Why won’t my GE washing machine drain?

A:

You did not tell me whether or not the drain pump runs at all. If it does not run, I can give you some checks to determine the cause of the issue. If you are not already sure you can perform these checks safely and competently, refer this work to a qualified professional. Working with live electrical current can be very hazardous and possibly deadly. Testing voltage output requires working with electrical current. Do not attempt this measurement without the proper tools and safeguards.

Gain access to the CCU (Central Control Unit), the teardown instructions are included below. Always unplug or de-energize electrical equipment before removing covers or attempting service. Be careful and wear appropriate hand protection when working around sharp metal parts. Find the connectors P8-1 or B-16 (black wire) and P8-5 or W-16 (white wire). With the unit in drain check the VAC (Voltage Alternating Current) across these terminals. It should be 120.0 VAC, if not the CCU is bad. If you have 120 check again, this time at the pump. If you have 120 the pump is bad, if you do not have 120 check the wiring and connections.

If you require further assistance please resubmit question with details of the checks you have made. I will be looking forward to helping you again in the near future.

Read More
Landell -
Sears Technician
January 08, 2010

Top Parts