Model #ATF8000FS1 FRIGIDAIRE Residential Washers

  • Control Panel
    3 Results
  • Cabinet/top
    3 Results
  • Motor/tub
    3 Results
  • Wiring Diagram
    3 Results
  • Wiring Diagram
    3 Results
Find part by diagram >

Error Codes

Error Code:

Condition:

Check/Repair:

Question and Answers

Q:

Frigidaire front load washer will lock and then stop ATF8000FS1

A:

Thank you for choosing SearsPartsDirect.com and being a valued member.  I can certainly understand how frustrating it can be when your washer is not working properly.

 
In the J2 plug on the console control, measure voltage

from the black wire to ground with power on.

0 volts. Check the door strike. If good, replace the
door switch assembly. 120 volts. Replace the console control board.

1. Start the diagnostic test. Turn the program knob 8
clicks clockwise from the start position.

Washer spins. Defective door lock assembly.
Washer does not spin. Defective control board.


Diagnostic Test
The diagnostic test is used to check individual component function only .
TO START THE TEST:
• Turn the Program Knob to the start position of the cycle furthest to the left.
• Press Start/Pause to start the cycle and save it.
• Press Cancel to stop the cycle and turn off the LEDs.
• Press Cancel again to turn on the LEDs.
• Within 5 seconds, press and hold the Options and Start/Pause buttons until LEDs start sequentially chasing, then release buttons.
1. All the LEDs will sequentially light. Pressing a button below a light cluster will light all the LEDs in that cluster at one time to confirm functionality.
2. Turn the program knob (1) click clockwise from the start position. The hot water solenoid will activate and hot water should enter through the
detergent compartment.
3. Turn the program knob (2) clicks from the start position. The bleach water solenoid will activate and cold water should enter through the bleach
compartment.
4. Turn the program knob (3) clicks from the start position. The bleach and the wash water solenoids will activate and cold wate r should enter
through the softener compartment.
5. Turn the program knob (4) clicks from the start position. The door lock solenoid will deactivate and the loading door can be opened. When the door
is opened, the drum light should turn on.
6. Turn the program knob (5) clicks from the start position. The washer will fill and tumble. Once tumbling has started, the Boo st Heater (if so
equipped) will turn on.
7. Turn the program knob (6) clicks from the start position. The drain pump & door lock solenoid will activate and the washer will operate in high spin.
SAFETY WARNING: If power is removed during this test, the door can be opened. To prevent injury, DO NOT put your hands inside when the tub
is rotating.
8. Turn the program knob (7) clicks from the start position. The control will signal the last error code.
Exiting Diagnostic Mode
There are two options for exiting the Diagnostic Test mode and returning the washer to normal operation:
a) Unplug the power cord, wait 5-8 seconds, then reconnect the power cord OR
b) Turn the program knob clockwise 2 or 3 clicks after the start position. Press Options and Start/Pause buttons together for a few seconds until
wash cycle LEDs appear .

You can also visit searpartsdirect.com for parts, diagrams, and repair information.

If you do not feel confident repairing this problem yourself, then you can have it repaired at your home by a Sears technician. Here is a link for the website: Sears Home Services .

Thank you for your question. Have a great day.

SAFETY NOTICE: Be sure to disconnect power to the appliance before performing any repairs. If you are not comfortable with doing any voltage checks that might be recommended, please contact your local service provider for repairs. Be aware that there could be sharp edges inside the appliance that could cause cuts or other injuries to yourself or others.

Read More
Natasha12 -
Sears Technician
July 29, 2015
Q:

My ATF8000FS1 Model turns on throws a bit of water starting at minute 53 and it stops at minute 52. ATF8000FS1 Frigidaire Washer

A:

Thank you for choosing Sears Parts Direct. I will be more than happy to help with your washer. Upon researching model ATF8000FS1: the “E75” error code indicates a water temperature sensor error or dispensing problem. You can unplug the washer power cord and remove the dispenser valve. With the dispenser valve removed you can test the valve using a multi meter. If the valve reads around 50Kohms of resistance then its ok and the control board may need to be replaced. If the valve test reads no continuity then you may need to replace the water valve. I have posted a link of the water valve to view the link click here.

I trust this information will help you, we appreciate your business thank for choosing Sears.

Read More
CarlosZ -
Sears Technician
June 17, 2015
Q:

washer turns on does not fill with water tech said motor is good needs a new control panel ATF8000FS1 Frigidaire Washer

A:

Thanks for the inquiry and for using SearsPartsDirect.com.
I don't think a control panel would be the part needed, it's probably what's inside of that panel, the electronic control board. 
For convenience, I have provided blue links below for both parts, the control board and the control panel. 

Electronic Control Board for Model ATF8000FS1

Control Panel for Model ATF8000FS1

Hope this helps and thanks for using SearsPartsDirect.com. We appreciate your business. 

Read More
Jeff Wallace Sr -
Sears Technician
July 31, 2014

Top Parts