Model #AF BECKETT Burner, Furnace

  • Unit Parts
    3 Results
Find part by diagram >

Question and Answers

Q:

Axle does not fit...Model # 536270340 CRAFTSMAN mid-engine riding mower 536.270340

A:

The picture did not display, so here is a direct link http://i26.photobucket.com/albums/c105/DanBabb/3740016C-68B0-49AF-84A9-777950CB5689_zpsxjqidjjl.jpg

Read More
DAN -
August 16, 2015
A:

I really need an Expert to answer this question for me. The 'guaranteed to fit' part does not fit.

Read More
DAN -
August 17, 2015
A:

T this point I would suggest having a technician come and check out what you have and determine what you need for your tractor. They may be reached at 1-800-469-4663. 

Read More
Jeffrey8673 -
Sears Technician
November 14, 2015
See more answers
Q:

E 24 error on Bosch dishwasher

A:

Bosch dishwashers are a great convenience, especially whey functioning properly. The link provided below may give you an idea of what may be happening with your dishwasher while waiting on a specific model error code of E24.

Read More
Anna T -
October 31, 2012
A:

The code indicates a drain problem. I would expect there to be a drain pump failure unless there is a loose connection at the drain pump. If the drain hose goes to a disposal make sure the plug in the disposal has be knocked out. The unit should be level. One thing about the E:24 error is that by definition the error means the drain pump is running but no water is being drained so look for a blockage in the drain line. If you're sure the lines are not blocked and the disposal plug is out and the drain pump does run and drain the water then it might be a control board problem. With the toe panel off you should be able to confirm if the drain pump is running. I hope this helps. You can reply with any additional details and a model number for further assistance.

Read More
Fred M -
Sears Technician
November 01, 2012
A:

hi Fred, I have the sam eproblem. I have Bosch Dishwasher Mod#SHE6AF02UC/06, E24 error code water is not pumping in. I have checked the drain, thats not an issue at all. I pulled the switch at the base and water drains out with no issues. When ever I run the cycle it keeps giving me the error and the water does not pump in. Pls advise thanks

Read More
rajm -
January 10, 2013
A:

If the water drains then the door switch is okay. The water valve may be the problem. At this point the next step would be checking voltage to the water valve across the two purple wires. Voltage and no water then the valve is bad. No voltage then the control is at fault.

Read More
Fred M -
Sears Technician
January 11, 2013
A:

Just an FYI. While E24 is an error that doe indicates water drain/pump issues or clogs -- if that all seems ok this is what I have found.... -- during the main power up -- if the main motor senses it is drawing more current than normal -- you'll get this error. Further -- if you've been using one of those "all in one" cleaning tablets that have rinse agent built in -- And you put in rinse agent into it's container -- the excess SUDSING due to excess rinse aid may be activating an anti flooding switch -- also causing this error. Concerning the main pump motor -- overdraw of current could be due to calcium build up -- especially if you are not using the proper SALT (which is not easy to find). A solution is a regular cleaning with a bit of CLR. Note this will cause SUDS too. So clean -- run, repeat, then run a couple times with NO CLR Then remember also NOT to use a dishwasher soap that contains a rinse agent. And lastly -- be sure to test your water and use approved dishwasher salt. only.

Read More
Ron -
October 03, 2013
A:

My Bosch dishwasher has thrown that E-24 code infrequently for months and now it has the code and won't fill and run at all. I poured water into the dishwasher manually and all it does is pump the water out but does not continue running. What do you think is wrong?

Read More
Gary -
December 17, 2014
A:

My Bosch dishwasher has thrown that E-24 code infrequently for months and now it has the code and won't fill and run at all. I poured water into the dishwasher manually and all it does is pump the water out but does not continue running. What do you think is wrong?

Read More
Gary -
December 17, 2014
A:

I had this message on mine also all I did was took the drainage componenant out of the bottom of the washer it just twists out and cleaned it out really good , then where the door latches at the top there is a little lever I pushed backwards until it snapped , and had nothing in the washer and set it to quick wash and held the button down until it started flashing and then pressed it again the start button that is and it started right up

Read More
shirley -
October 26, 2015
See more answers
Q:

AF error code WED6200SW1 Whirlpool Residential dryer