Model #A80 PIONEER Misc Audio

  • No Image Available - Fidelitone
    3 Results
Find part by diagram >

Question and Answers

Q:

Where can I find a manual for DieHard Battery Charger model KH-20A 80/20/10/2 amp 12 volt?

A:

Clarifying the model is DH-20A, not KH-20A as in the title. Sorry.

Read More
Lee -
June 10, 2012
A:

Battery chargers are great to gave around. The error codes can be frustrating. I found some information for you that I am hoping will help you. I am adding the link below to a manual for a Craftsman battery charger to help you with your question while you wait for your expert response. It may take your expert 24-48 hours. I do hope that this will help. Page 11 has information about the error codes.

Read More
Marc H -
June 10, 2012
A:

Marc H -- You certainly found something which at least gives me a clue. Interestingly I found this model as well on Sears site, but with a different prefix and it either did not have the error code list or I missed it. Not certain the codes will be the same for my model but this at least gives me something to start with -- thanks for your help. Looks like a good site to be aware of too. Thanks again.

Read More
Lee -
June 10, 2012
A:

Thanks for contacting ManageMyLife.com. I understand your concern in looking for a owner manual for a battery charger. We are here to help. This battery charger is manufactured by Schumacher. I provided you a link to Schumacher manuals. Just click here to view that site. I hope this helps.

Please feel free to let me know if you need further assistance. We are always here to help.

Thank you for using ManageMyLife.com.

Read More
John H -
Sears Technician
June 12, 2012
A:

John H I am not certain as to which model you believe corresponds to my 80/20/10/2 charger. I can find some that are close (Sears 71227) but haven't found the specific unit I have. Is there a model or manual number that I can use?

Read More
Lee -
June 15, 2012
A:

John H Sorry. I just didn't look long enough. The DH-20 was the next to last item on the 13 pages of manuals. Thank you.

Read More
Lee -
June 15, 2012
See more answers
Q:

ADMIRAL: GAS DRYER MODEL# LNC75433A80/LNC85433A80

A:

I understand your concern toward wanting to make sure your Dryer is working properly. I have taken the time to research on the Manage My Life website and have located information that you may find helpful. While you are waiting for a detailed answer from an expert I have added the links below. Hope this helps

Read More
Priscilla V -
January 18, 2012
A:

Thank you for your question and I understand your concern.

If the igniter is not glowing red it could have a broken igniter, faulty flame sensor, control thermostat, high limit thermostat, thermal fuse, faulty motor centrifugal switch or timer. You will not likely have to replace the burner assembly or gas valve. I was not able to locate the wiring diagram by any one of the two model numbers you provided. I strongly suggest calling a service technician to diagnose and repair the gas dryer.

If you do not feel confident repairing this problem yourself, then you can have it repaired at your home by a Sears technician. Here is a link for the website: Sears Home Services .

Read More
Joey S -
Sears Technician
January 19, 2012
See more answers
Q:

WHAT IS THE FIRST STEPS TO REPLACEMENT OF AUTOMATIC DRYER HEATER IGNITER UNIT FOR MODEL NUMBER # LNC8543A80 /LNC7543A80 SERIAL: 29H108291 BY ADMIRAL? 31001556#

A:

I think its great that you are wanting to do some repairs on your own. While you are waiting for an expert to respond, I have attached some helpful links below that may provide information to assist you with your question.

Read More
Joseph P. -
January 11, 2012
A:

Thank you for your question and I understand your concern. The two model number provided does not appear to be valid models. I assume it's a gas dryer and not an electric dryer.

The first step is to disconnect the power cord from the power source. The front panel will have to be taken off in order to access the glow bar igniter. There are screws along the bottom of the front panel that will need to be removed. Once the screws are removed, tilt the bottom of the front panel outwards and pull it down in order disengage the panel from the two upper clips. The igniter will be located along the end of the burner assembly. Remove the screw securing the igniter to the burner and disconnect the wire connector and remove the igniter. Reverse the procedure to install. NOTE: Be careful with the new igniter. It is very fragile. I hope this is helpful. If I may be of further assistance as more details become available, please reply to this post.

Read More
Joey S -
Sears Technician
January 13, 2012
See more answers