Model #9901 WEBER Grill, Gas

  • Summit Sideburner For The Cart
    3 Results
Find part by diagram >

Question and Answers

Q:

Is oven light switch normally closed? Kenmore Electric Range 790.9901

A:

The correct switch part number is 316209900.

Read More
George -
September 22, 2014
A:

Thank You for choosing Sears PartsDirect.com and being a valued member. It is unfortunate to hear that you are having issues with your oven light and I do understand your frustration. Glad to help out. I'm looking at your model number 79099012100 and I would suggest that you remove the power to the range and pull the range out and remove the 4 screws in the cook top for the burners and the use a putty knife type tool to depress the spring clips that holds the cook top down to the chassis and then you should be able to get to the top screws that holds the side panel onto the inner panel and then remove the screws on the back that holds the side panel onto the range. 

Make sure you have removed power to the range because most of the door switches do not have shielding on the wire terminals and they are hot. 

When you get the new switch retrieve the switch wires and feed them through the hole in the front and connect to the switch and push the switch into the oven front frame. Re-assemble the range. I have included a link to our PartsDirect page where you can purchase the part you need to complete your repair. Just click the blue link above to be taken to the page. I trust this information will help you.

 

Thank you for choosing Sears PartsDirect.com.

 

SAFETY NOTICE: Be sure to disconnect power to the appliance before performing any repairs. If you are not comfortable with doing any voltage checks that might be recommended, please contact Sears for repairs. Be aware that there could be sharp edges inside the appliance that could cause cuts or other injuries to yourself or others.

Read More
Sherman_G_Wallace -
Sears Technician
September 24, 2014
See more answers
Q:

my Kenmore electric built in oven doesn't heat up

A:

Having your oven fail to heat can be a real headache. I would suggest that you provide a little more information such as the make and COMPLETE model number of your product, so your expert will be able to provide you with the best possible answer. Just click on reply down below, where you can provide the additional information.

Read More
Julio -
June 04, 2013
A:

It's a Kenmore electric built in oven; model # is 790.48839901. Do you need the serial #? It was purchased in 2011. I used it last week, ran the self cleaner on Saturday, tried to use it today and it didn't heat up. The buttons all work; you can turn it on but it stays in pre-heat mode, never heating up. I tried to use just the broiler but it didn't work either.

Read More
Tracy -
June 04, 2013
A:

 

 Thank you for choosing ManageMyLife.com and allowing us to help you. When your oven stops heating after a self-clean cycle or a high temperature baking cycle. It is likely that the safety thermostat located on the back of the unit behind the rear cover panel has tripped open, thus cutting power to the heating elements. This can happen under certain conditions and installations. This can also happen if the cooling fan fails or there is blockage in your venting sytem. If it is venting to the outside, check for a bird nest or other blockage at the roof jack. You will want to make sure the fan spins freely and is not binding as well. You will need to remove the wall oven and the rear panel to access the tripped safety thermostat. You could re-set the safety thermostat by pushing the red button in and it will operate again unless it trips again when you use the self clean feature. If you do not feel comfortable repairing this problem yourself, you can have it repaired at your home by a Sears technician. Click here to schedule service online at the Sears Home Services website. A 10% discount coupon is available when service is set on line.

If you have any follow-up questions, please continue our conversation on this existing thread.

Thanks again for choosing ManageMyLife.com

Read More
James -
Sears Technician
June 07, 2013
See more answers
Q:

Error Code F9, for Kenmore Elite Electric Range.

A:

Having issues with the Range not working is not something any of us want to see. If you are technically handy, this is a good site to get instruction and fix some things yourself. If you do not feel confident doing your own repairs, an option is to visit Sears Home Services and use the scheduler. While you wait for the expert to review your model, you can check the bottom link for some possibilities. Hope this is of help.

Read More
Priscilla V -
February 13, 2012
A:

Thank you for your question and I understand your concern.

The "F9" fault code implies the electronic oven control has detected a latch motor assembly problem. The latch motor wiring should be checked and the latch motor replaced if there is no wiring issues between the control board and latch motor. The latch motor is located at the back of the range. The back panel will need to come off in order to access the lock motor. NOTE: Disconnect the range from the power supply before removing the rear panel. I added an image of the door lock below with removal instructions.

This may be the issue. If not, please reply and I will be glad to assist you further.

Read More
Joey S -
Sears Technician
February 14, 2012
See more answers