Model #979 TROYBILT Walk Behind Lawnmower, Gas

  • Deck/blade/handle/wheels
    3 Results
  • Housing/transmission Assembly
    3 Results
Find part by diagram >

Question and Answers

Q:

Where can I find instructions to run the diagnostics for a MDBH979AWB3 maytag dishwasher.

A:

Dishwashers are great for cleaning the dishes and they help save time. I did some research on your model number but was not able to find out how to enter the diagnostics mode. Your expert will be able to help answer your question. It may take 24-48 hours. I do hope everything works out with the dishwasher.

Read More
Marc -
September 19, 2012
A:

Thank you for your question and I understand your concern.

To invoke the Diagnostics Cycle, perform the following key presses or actions in less than 6 seconds while in standby:

Heated Dry---Normal---Heated Dry---Normal

I also added images below with the technical data sheet. The technical data sheet is located under the tub or behind the lower access panel.

I hope this is helpful. If I may be of further assistance as more details become available, please reply to this post.

Read More
Joey S -
Sears Technician
September 20, 2012
A:

Thank you for the info. I attempted to run the Diagnostics Cycle, however the Normal key does not function. I conducted the keypad operation test. The control is working properly, without the keypad attached. It appear that steam is leaking out of top right front corner of the dish washer and doing damage to the countertop. I read another post about putting washer behind the door latch to make close the door tighter, will this help? I ordered a new control panel, I assume this is a new keypad as well. This is the second new control panel that has been replaced in the last eight months. Thanks Again

Read More
Denny -
September 23, 2012
A:

Denny: If the door is not sealing in the upper right corner it may need a new door seal or the dishwasher may not be sitting square or level. Also, check the seal where the vent assembly mates to the inner door panel. Steam could be leaking past the vent seal into the control panel area too.

Read More
Joey S -
Sears Technician
September 24, 2012
A:

OK Thanks, looks like I will have to take it out from under the countertop to see the extent of the damage. I'll check the level. The seals look good. Just waiting on the control panel to arrive.

Read More
Denny -
September 24, 2012
A:

Joey, could the dishwasher being wired without a three prong plug be causing this control panel issue?

Read More
Denny -
September 24, 2012
A:

Denny: It could cause electrical issues but it would not cause steam. Steam or moisture can cause issues with the touch panel or control. The dishwasher should be grounded if it's not. The dishwasher should be connected with a ground wire.

Read More
Joey S -
Sears Technician
September 24, 2012
A:

I have this model dish washer. When I reset the panel all the lights come on but will not reset when I push the cancle button. What test can I do to find out if the problem is the panel,board or other. I don't want to replace good parts.

Read More
Bill -
December 13, 2015
See more answers
Q:

How do I replace Gas cook top velve? jgp979bef2bb jgp979bef2bb

A:

Thank you for choosing Searspartsdirect.com and being a valued member. I can certainly assist you.

Click here for video. It will assist with taking the unit apart to get to the valve. 

You can also visit searpartsdirect.com for parts, diagrams, and repair information.

If you do not feel confident repairing this problem yourself, then you can have it repaired at your home by a Sears technician. Here is a link for the website: Sears Home Services .

Thank you for your question. Have a great day.

SAFETY NOTICE: Be sure to disconnect power to the appliance before performing any repairs. If you are not comfortable with doing any voltage checks that might be recommended, please contact your local service provider for repairs. Be aware that there could be sharp edges inside the appliance that could cause cuts or other injuries to yourself or others.

Read More
Natasha12 -
Sears Technician
July 23, 2015
Q:

Maytag dishwasher stuck in quick wash cycle MDBH979SAB1 Maytag Undercounter dishwasher

A:

Thank you for your inquiry on your Maytag Dishwasher, Model: MDBH979SAB1. From reviewing the details on your model, I have provided an insert from the service manual which will provide you with information on how to start the diagnostics test for any error codes. 

Safety Warning: Before beginning the repair, disconnect the direct power supply to the dishwasher to prevent the risk of injury or any electrical shock.

If you don’t feel comfortable or confident in this repair, then you can have it repaired at home by a sears technician. I have the included a link to the website: Sears Home Services or call 1-800-469-4663.

 

I hope this answered your question. Thank you for contacting SearsPartsDirect.com, and have yourself a wonderful day. 

Read More
Gerry 93 -
Sears Technician
May 15, 2015
A:

Jerry, thanks for the information. I tried print the insert from the service manual you provided but it's too small to read. Thanks Alvin

Read More
Christina -
July 05, 2015
See more answers

Top Parts